Honeywell Chadwick-Helmuth 8500C Maintenance Manual Download Page 20

Page: 20 / 186

1-8

Chadwick-Helmuth A Business Unit of Honeywell International, Inc.

Chapter 1

- Introduction

Table 1-2. System Interconnect Cables

Part No.

Nomenclature

Purpose

Qty.

10811-12

Cable, Signal
Selector (12 ft)

Connects signals between 8500C/C+.

11210-50

Cable, Velocimeter
(50 ft)

Connects Velocimeter to 8520C or
8500C/C+ via 8998 cable.

up to 12

11210-20

Cable, Velocimeter
(20 ft)

Connects Velocimeter to 8520C or
8500C/C+ via 8998 cable.

up to 12

8998

Cable, Input
Adapter

Connects 8500C/C+ to power,
Velocimeter, and magnetic pickup/
photocell inputs when 8520C is not
used.

10813-12

Cable, DC Power
(12 ft)

Connects 28 VDC power to 8520C.

10808-25

Cable, Magnetic
Pickup (25 ft)

Connects magnetic pickup to 8500C/
C+ or 8520C via 10809 cable.

10185

Cable, Photocell

Connects optical probe to photocell
processor 10170

3529

Cable, DC Power
Extension

Connects DC power to 8500C/C+ or
8520C.

Table 1-3. Basic System Accessories

Part No.

Nomenclature

Purpose

Qty.

Model 11A

Calibrator

Bench tests 8500C/C+ system.

10170

Photocell Processor

Processes optical inputs for the
8500C/C+ via the 8520C or cable
8998.

135M-12

Strobex

Hand-held strobe, illuminates
reflective targets on blades for
tracking purposes.

11800

FasTrak

Day-Night optical tracker, used in
place of Strobex. Communicates with
8500C/C+ Smart Chart software.

10200

Optical Probe

Provides optical inputs to photocell
processor 10170.

Summary of Contents for Chadwick-Helmuth 8500C



























































































































































































Search results

Summary of Contents for Chadwick-Helmuth 8500C

Reviews:

Related manuals for Chadwick-Helmuth 8500C

Brands by name

Popular brands

Honeywell Chadwick-Helmuth 8500C, Maintenance Manual

Search results

Summary of Contents for Chadwick-Helmuth 8500C

Reviews:

Related manuals for Chadwick-Helmuth 8500C

Brands by name

Popular brands