Honeywell Chadwick-Helmuth 8500C Maintenance Manual Download Page 165

Page: 165 / 186

Functional Tests

8500C/8500C+ System Maintenance Manual

D-7

jj.

Press

START

key.

kk.

Verify that display indicates (example in Figure D-3):

1800+2 RPM

0.8+0.08 IPS

275+10°

ll.

Press

STOP

key.

mm.

Repeat steps bb. through ll. for all channels in Table D-2.

D.5.2

8500 Balancer/Analyzer System Test Procedure with 8520CS (Using

High Temp Accelerometers and Photocells)

NOTE: Thes tests build successively on the first test in this section. Any settings not
mentioned must be left as they were in the previous test.

D.5.2.1 Test Setup

Connect equipment as shown if Figure D-4.

NOTE: Make sure calibrator Accelerometer cables are free to move so that Accelerometer
movement is not inhibited.

D.5.2.2 Power-Up Self-Test

Hold down

START

key on 8500C/C+ and turn on power supply.

NOTE: This erases all memory in 8500C/C+.

Wait until

Power-Up Self-Test

display appears and release

START

key.

D.5.2.3 Balance Test

Ensure that the only one piece of reflective tape is installed on the Calibrator 11A rotor
CAM.

Set

CAM RATE (RPM)

switch to

1800

Set

MOTOR

switch to

Summary of Contents for Chadwick-Helmuth 8500C



























































































































































































Search results

Summary of Contents for Chadwick-Helmuth 8500C

Reviews:

Related manuals for Chadwick-Helmuth 8500C

Brands by name

Popular brands

Honeywell Chadwick-Helmuth 8500C, Maintenance Manual

Search results

Summary of Contents for Chadwick-Helmuth 8500C

Reviews:

Related manuals for Chadwick-Helmuth 8500C

Brands by name

Popular brands