manualshive.com logo in svg

Hitachi RAS-(2-3)HVRN(S)(2), Service Manual

The Hitachi RAS-(2-3)HVRN(S)(2) Service Manual is a comprehensive user guide for this advanced air conditioner model. With detailed instructions and illustrations, this manual is essential for troubleshooting, maintenance, and optimal utilization of the product. Download for free from manualshive.com and unlock the full potential of your Hitachi air conditioner.

Share
Download
background image

v

Contens

SMGB0064 rev.0 - 08/2011

1. General information .......................................................................................................1

1.1  General information ....................................................................................................................................2

1.1.1  General note .................................................................................................................................................... 2
1.1.2  Introduction ...................................................................................................................................................... 2
1.1.3  Environment-friendly units ............................................................................................................................... 2

1.2  Applied symbols ..........................................................................................................................................3

1.3  Product guide .............................................................................................................................................4

1.3.1  Classification of IVX series outdoor unit models ............................................................................................. 4
1.3.2  Classification of ES series outdoor unit models .............................................................................................. 4
1.3.3  Product guide: Outdoor units ........................................................................................................................... 5
1.3.4  Accessory code list .......................................................................................................................................... 6

2. Unit Installation ...............................................................................................................7

2.1  Safety summary ..........................................................................................................................................8

2.2  Transportation of outdoor unit .....................................................................................................................9

2.3  Center of gravity .......................................................................................................................................10

2.4  Factory-supplied accessories for RAS-(8-12)HRNM ................................................................................ 11

2.5  Installation space (Initial ckeck) ................................................................................................................12

2.5.1  RAS-3HVRNM2E / RAS-(2-3)HVRN(S)2 / RAS-(4-10)H(V)RNS2E ............................................................. 12
2.5.2  RAS-(4-6)H(V)RNM2E / RAS-(8/10)HRNSE ................................................................................................. 16
2.5.3  RAS-(8-12)HRNM ......................................................................................................................................... 20

2.6  Place provision .........................................................................................................................................22

2.6.1  Place provision for RAS-(3-12)H(V)RNM(2)(E) and RAS-(4-10)H(V)RNS(2)E ............................................. 22
2.6.2  Place provision only for RAS-(2-3)HVRN(S)2 ............................................................................................... 25

2.7  Optional parts and installation ..................................................................................................................28

2.7.1  Optional parts and installation for RAS-(2-3)HVRN(S)2 ................................................................................ 28
2.7.2  Optional parts and installation RAS-3HVRNM2E / RAS-(4-6)H(V)RNS2E ................................................... 33
2.7.3   Optional parts and installation RAS-(4-6)H(V)RNM2E / RAS-(8/10)HRNSE ............................................... 37
2.7.4  Optional parts and installation RAS-(8-12)HRNM ......................................................................................... 42

3. Piping work and refrigerant charge ............................................................................49

3.1  General notes ...........................................................................................................................................50

3.2  Piping work connection considerations.....................................................................................................52

Contents

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RAS-(2-3)HVRN(S)(2)

Haier HSU24VHG(DB)-G&W Service Manual preview
HSU24VHG(DB)-G&W
Brand: Haier Pages: 98
Gree DUCT09HP230V1BD Installation & Owner'S Manual preview
DUCT09HP230V1BD
Brand: Gree Pages: 24
Soleus Air PH5 Series Operating Instructions Manual preview
PH5 Series
Brand: Soleus Air Pages: 16
Hyundai HYUAP580 Instruction Manual preview
HYUAP580
Brand: Hyundai Pages: 52
Dometic Breathe Easy Installation And Operating Manual preview
Breathe Easy
Brand: Dometic Pages: 136
Nordyne E3 Series and Owner'S Manual & Installation Instructions preview
E3 Series and
Brand: Nordyne Pages: 36
Ballu KFR-3601GW Service Manual preview
KFR-3601GW
Brand: Ballu Pages: 46
Carrier Comfort 24ACS Installation Instructions Manual preview
Comfort 24ACS
Brand: Carrier Pages: 6
Galletti FM 22/23 User, Installation & Maintenance Manual preview
FM 22/23
Brand: Galletti Pages: 104
GE AEH06LV Owner'S Manual And Installation Instructions preview
AEH06LV
Brand: GE Pages: 28
Dutch originals DO-CH-ACL150DRT User Manual preview
DO-CH-ACL150DRT
Brand: Dutch originals Pages: 48
DayRelax XQS140UY1 User Manual preview
XQS140UY1
Brand: DayRelax Pages: 100
Ingersoll-Rand Precedent WSC072E Installation, Operation And Maintenance Manual preview
Precedent WSC072E
Brand: Ingersoll-Rand Pages: 68
Airwell AWAU-YGD009-H11 Service Manual preview
AWAU-YGD009-H11
Brand: Airwell Pages: 54
Toyotomi M01-R32 Owners And Installation Manual preview
M01-R32
Brand: Toyotomi Pages: 37
Technibel GR9FI110R5I series Installation Instructions Manual preview
GR9FI110R5I series
Brand: Technibel Pages: 64
Carrier 38GNA Installation And Start-Up Instructions Manual preview
38GNA
Brand: Carrier Pages: 8
Danby DPA060B1WDB-RF Owner'S Manual preview
DPA060B1WDB-RF
Brand: Danby Pages: 67

Brands by name

Popular brands

Load more brands