Hitachi RAS-(2-3)HVRN(S)(2) Service Manual Download Page 22

Page: 22 / 488

2 Unit Installation

SMGB0064 rev.0 - 08/2011

2.5 Installation space (Initial ckeck)

2.5.1 RAS-3HVRNM2E / RAS-(2-3)HVRN(S)2 / RAS-(4-10)H(V)RNS2E

Blocked in Inlet Side

Upper Side Open

Single Installation

Multiple Installation (Two units or more)

Pipe Cover

Ensure 250 mm or more of the side space on the pipe cover side.

Allow 250 mm of space between units. Leave open both right and left

sides.

Pipe Cover

Be sure to use the fan direction guide. Leave open both right and left sides.
Ensure 250 mm or more of the side space on the pipe cover side.

Be sure to use the fan direction guide.
Allow 250 mm of service space between units. Leave open both right

and left sides. When subject to direct sunlight on the back wall ensure

the length marked with

be 400 or greater.

Ensure 250 mm or more of the side space on the pipe cover side.

Upper Side Blocked

Single Installation

Multiple Installation (Two units or more)

Pipe Cover

Fifteen mm of space is acceptable for one of the lateral sides.
Ensure 250 mm or more of the side space on the pipe cover side.

Allow 250 mm of service space between units. Leave open both right

and left sides.
Ensure 250 mm or more of the side space on the pipe cover side.

Be sure to use the fan direction guide. Leave open both right and left sides.
Ensure 250 mm or more of the side space on the pipe cover side.

Be sure to use the fan direction guide.
Allow 250 mm of service space between units. Leave open both right

and left sides. Serial installation allowed up to two units.
Ensure 250 mm or more of the side space on the pipe cover side.

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Search results

Summary of Contents for RAS-(2-3)HVRN(S)(2)

Reviews:

Related manuals for RAS-(2-3)HVRN(S)(2)

Brands by name

Popular brands

Hitachi RAS-(2-3)HVRN(S)(2), Service Manual

Search results

Summary of Contents for RAS-(2-3)HVRN(S)(2)

Reviews:

Related manuals for RAS-(2-3)HVRN(S)(2)

Brands by name

Popular brands