Hitachi RAS-(2-3)HVRN(S)(2) Service Manual Download Page 477

Page: 477 / 488

12 Maintenace notes

467

SMGB0064 rev.0 - 08/2011

12.6 Not cooling well due to insufficient installation space for the outdoor unit

Question and answer for the field work

Example 5: Not cooling well due to insufficient installation space for outdoor unit

Phenomenon

Cooling operation was well performed through the intermediate season. However the cooling operation was not well avai-

lable when the outdoor temperature was higher than 35 °C.

Cause

As the outdoor units were installed without a sufficient installation space the hot discharge air from other outdoor units was

circulated.

In this case though the outdoor temperature was 35 °C the actual suction air temperature was nearly 50 °C and protection

system from excessively high suction pressure was activated the frequency of the compressor was decreased and the

cooling capacity was also decreased accordingly.

As the outdoor units in-line were installed back to back with a distance of 600 mm between each outdoor unit’s back the

hot discharged air from other outdoor units was circulated.

Countermeasure

Ensure that sufficient space should be secured for multi-row and multiple-installation.

Keep a distance of more than 15 mm between other units

and do not put obstacles on the right and left sides. Dimen-

sion B is as shown below.

0 < L < 1/2H

600 or more

300 or more

1/2H < L < H

1400 or more

350 or more

N O T E

•

If L is larger than H mount the units on a base so that H is greater or equal to L.

•

In this situation ensure that the base is closed and does not allow the airflow to short circuit.

•

When the mark * dimension is secured be sure to mount the airflow guide.

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Search results

Summary of Contents for RAS-(2-3)HVRN(S)(2)

Reviews:

Related manuals for RAS-(2-3)HVRN(S)(2)

Brands by name

Popular brands

Hitachi RAS-(2-3)HVRN(S)(2), Service Manual

Search results

Summary of Contents for RAS-(2-3)HVRN(S)(2)

Reviews:

Related manuals for RAS-(2-3)HVRN(S)(2)

Brands by name

Popular brands