Hitachi RAS-(2-3)HVRN(S)(2) Service Manual Download Page 215

Page: 215 / 488

8 Troubleshooting

205

SMGB0064 rev.0 - 08/2011

Alarm codes for IVX and ES Series

Code

No.

Category

Type of Abnormality

Main cause

Indoor unit

Activation of protection device

Failure of fan motor, drain discharge, PCB, relay, float switch

activated.

Outdoor unit

Activation of protection device

Activation of PSH, locked motor, abnormal operation in the

power supply phase.

Transmission

Abnormality between indoor (or outdoor) and outdoor

(or indoor) units

Incorrect wiring. Failure of PCB. Tripping of fuse. Power

supply OFF.

Abnormal operation between inverter and control

PCB

Transmission failure between inverter PCBs

Power supply

Abnormal power supply

Power source with abnormal wave pattern.

Voltage drop

Voltage drop due to excessively low or high voltage in

outdoor unit

Voltage drop in power supply. Incorrect wiring or insufficient

capacity of power supply wiring.

Cycle

Drop in discharge gas overheating

Excessive refrigerant charge. Expansion valve lock open.

Increase in discharge gas temperature

Insufficient refrigerant charge, refrigerant leakage. Expansion

valve closed or clogged.

Sensor in indoor

unit

Inlet air thermistor

Failure of thermistor, sensor, connection.

Outlet air thermistor

Anti-freeze thermistor

Gas pipe thermistor

Fresh Outdoor Air Thermistor (Econofresh)

Protection device for fan motor is triggered

Failure of fan motor

Outdoor unit

sensor

Compressor thermistor

Failure of thermistor, sensor, connection.

Outside air thermistor

Evaporation thermistor

System

Incorrect setting of outdoor and indoor units

Incorrect setting of capacity code.

Incorrect setting of indoor unit number

Duplication of indoor unit number.

Abnormality of protective circuit in outdoor unit

Failure of indoor unit PCB; incorrect wiring; connection to

indoor unit PCB.

Pressure

Cooling overload (possible activation of high pressure

device)

O.U. pipe thermistor temp. is higher than 55 ºC and the

compressor top temp. is higher than 95 ºC, O.U. protection

device is activated.

Heating overload (high-pressure device may be

activated)

If I.U. freeze protection thermistor temp. is higher than 55 ºC

and compressor top temp. is higher than 95 ºC, O.U. protec-

tion device is activated.

Activation of protection device for low pressure drop

Stoppage due to excessive decrease of evaporating temper-

ature (Temp < -35 ºC) is activated 3 times in one hour, motor

locked in heating mode.

Inverter

Activation of overcurrent protection

Overload, overcurrent. Failure of DIP IPM, IPM or PCB2,

heat exchanger clogged, locked compressor.

Abnormality in inverter current sensor

Incorrect wiring of current sensor. Failure of control PCB, DIP

IPM, IPM or PCB2.

Abnormal thermistor of inverter fin (for inverter fin

temperature)

Shorcircuit or incorrect wiring

Activation for protection of DIP IPM, IPM or PCB2

Abnormality of DIP IPM or PCB2

Compressor failure, heat exchanger clogged.

Increase in inverter fin temperature

Abnormal inverter fin thermistor

Heat exchanger clogged.

Abnormal outdoor fan.

Abnormality of DIP IPM, IPM or PCB2

Failure of DIP-IPM, IPM or PCB2.

Outdoor fan

Fan motor abnormality

Disconnected wire or incorrect wiring between control PCB

and inverter PCB.

Incorrect wiring or abnormality in fan motor.

Inverter

Abnormal inverter fin thermistor (for the temperature

of inverter fin)

Lost terminals, disconnected wire, failure of inverter thermis-

tor.

Compressor

Compressor protection alarm

Compressor failure.

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Search results

Summary of Contents for RAS-(2-3)HVRN(S)(2)

Reviews:

Related manuals for RAS-(2-3)HVRN(S)(2)

Brands by name

Popular brands

Hitachi RAS-(2-3)HVRN(S)(2), Service Manual

Search results

Summary of Contents for RAS-(2-3)HVRN(S)(2)

Reviews:

Related manuals for RAS-(2-3)HVRN(S)(2)

Brands by name

Popular brands