manualshive.com logo in svg

Hitachi RAS-(2-3)HVRN(S)(2), Service Manual

The Hitachi RAS-(2-3)HVRN(S)(2) Service Manual is a comprehensive user guide for this advanced air conditioner model. With detailed instructions and illustrations, this manual is essential for troubleshooting, maintenance, and optimal utilization of the product. Download for free from manualshive.com and unlock the full potential of your Hitachi air conditioner.

Share
Download
background image

vii

Contens

SMGB0064 rev.0 - 08/2011

5. Control System ........................................................................................................... 117

5.1  Device control system............................................................................................................................. 118

5.1.1  Device control system for IVX Series ...........................................................................................................118
5.1.2  Device control system for ES Series ........................................................................................................... 120

5.2  Outdoor units PCB ..................................................................................................................................122

5.2.1  Outdoor units PCB for IVX Series ............................................................................................................... 122
5.2.2  Outdoor units PCB for ES Series ................................................................................................................ 123

5.3  Protection and safety control ..................................................................................................................126

5.3.1  Protection and safety control for IVX Series ................................................................................................ 126
5.3.2  Protection and safety control for ES Series ................................................................................................. 127

5.4  Standard operation sequence.................................................................................................................128

5.4.1  Standard operation sequence for IVX Series .............................................................................................. 128
5.4.2  Standard operation sequence for ES Series ............................................................................................... 135

5.5  Standard control functions ......................................................................................................................142

5.5.1  Standard control functions for IVX Series ................................................................................................... 142
5.5.2  Standard control functions for ES Series .................................................................................................... 151

6. Optional functions ......................................................................................................161

6.1  Outdoor units IVX and ES series ............................................................................................................162

6.1.1  Available ports ............................................................................................................................................. 162
6.1.2  Configuration ............................................................................................................................................... 164
6.1.3  Description of optional input signals ............................................................................................................ 165
6.1.4  Description of optional output signals .......................................................................................................... 166
6.1.5  Optional functions ........................................................................................................................................ 167

7. Test Run ......................................................................................................................173

7.1  Checking procedure before the test run .................................................................................................174

7.2  Test run procedure using the remote control switch ...............................................................................176

7.3  Test run procedure using the wireless remote control switch .................................................................178

7.4  Test run procedure from the outdoor unit side ........................................................................................180

7.5  Check list ................................................................................................................................................181

7.5.1  Check list for IVX Series .............................................................................................................................. 181
7.5.2  Check list for ES Series ............................................................................................................................... 189

8. Troubleshooting .........................................................................................................195

8.1  Initial troubleshooting for IVX an ES Series ............................................................................................196

8.1.1  Checking by means of the 7-segment display ............................................................................................. 196
8.1.2  Failure of the power supply to the indoor unit and the remote control switch ............................................. 197

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RAS-(2-3)HVRN(S)(2)

Daikin MC80ZBFVM Operational Manual preview
MC80ZBFVM
Brand: Daikin Pages: 44
Lennox VEMD007N432U Installation Manual preview
VEMD007N432U
Brand: Lennox Pages: 32
Wagan USB Deluxe Air Purifier User Manual preview
USB Deluxe Air Purifier
Brand: Wagan Pages: 20
aircon MDV MOB02-18HFN8-QRD0GW Owner'S Manual & Installation Manual preview
MDV MOB02-18HFN8-QRD0GW
Brand: aircon Pages: 120
Bestron 8712184052547 Instruction Manual preview
8712184052547
Brand: Bestron Pages: 52
dirna Bergstrom bycool green line SLIM COOL TRR Troubleshooting Manual preview
bycool green line SLIM COOL TRR
Brand: dirna Bergstrom Pages: 68
Daitsu APD 9AM Instruction Manual preview
APD 9AM
Brand: Daitsu Pages: 56
ICP PAF Series Installation Instructions Manual preview
PAF Series
Brand: ICP Pages: 14
Daikin FTXD50BVMA Operation Manual preview
FTXD50BVMA
Brand: Daikin Pages: 32
Koldwave 5WK Series Operation Manual preview
5WK Series
Brand: Koldwave Pages: 34
Daikin ETVZ12S18EA6V ETVZ12S23EA6V Operation Manual preview
ETVZ12S18EA6V ETVZ12S23EA6V
Brand: Daikin Pages: 24
Vertiv Liebert CRV Plus User Manual preview
Liebert CRV Plus
Brand: Vertiv Pages: 98
COMFORT-AIRE REG-123M Owner'S Manual preview
REG-123M
Brand: COMFORT-AIRE Pages: 20
Carrier CPFILTRK007A00 Installation Instructions preview
CPFILTRK007A00
Brand: Carrier Pages: 4
Essick EC302 Instruction Manual preview
EC302
Brand: Essick Pages: 4
Daikin FDXM35F3V1B Installer'S Reference Manual preview
FDXM35F3V1B
Brand: Daikin Pages: 20
Daikin FDXM25F3V1B Operation Manual preview
FDXM25F3V1B
Brand: Daikin Pages: 8
Samsung CH070EAMC Service Manual preview
CH070EAMC
Brand: Samsung Pages: 126

Brands by name

Popular brands

Load more brands