Hitachi RAS-(2-3)HVRN(S)(2) Service Manual Download Page 190

Page: 190 / 488

7 Test Run

180

SMGB0064 rev.0 - 08/2011

7.4 Test run procedure from the outdoor unit side

The test run procedure from the outdoor unit side is shown below.
You can set this DIP switch while the power source is ON.

Setting of dip switch

DSW1

Cooling: Pin 1 ON

Heating: Pin 1, 2 ON

Cooling intermediate season: Pin 1, 3 ON

Heating intermediate season: Pin 1, 2, 3 ON

Manual compressor OFF: Pin 4 ONe

D A N G E R

•

Do not touch any other electrical components while you are setting the switches on the PCB.

•

Do not attach or detach the service access panel when the power source for the outdoor unit is ON and the

outdoor unit is operating.

•

Set all the DIP switches of DSW1 to OFF after completing the test run.

Dip switch seting

Operation

Remarks

Test run

1. Setting operation mode

•

The indoor unit automatically

starts to operate when the

test run of the outdoor unit

is set.

•

You can perform the ON/OFF

operation from the remote

control switch or the DSW1

of the outdoor unit.

•

Continuous operation during

2 hours is performed without

the Thermo-OFF condition.

•

Make sure that the indoor

units start to operate in

accord with the test run of

the outdoor unit.

•

If you start the test run from

the outdoor unit and you stop

the test run from the remote

control switch, the test run

function of the remote control

switch is cancelled. Howe-

ver, the test run function

of the outdoor unit is not

cancelled.

•

If the more than one indoor

unit is connected with one

remote control switch, all the

units start the test run at the

same time. Therefore, turn

OFF the power source so

that the indoor units do not

perform the test run. If this is

the case, the TEST RUN in-

dication of the remote control

switch may flicker. This is not

abnormal.

•

The setting of DSW1 is not

required for the test run from

the remote control switch.

(a) Cooling:

Set DSW1-1 ON

(b) Heating

SET DSW1-1 and 2 ON

season:

Set DSW1-1 and 3 ON

(d) Heating intermediate

season:

Set DSW1-1, 2 and 3 ON

Manual OFF of com-

pressor

2. Forced stoppage of compressor:

•

When DSW1-4 is ON during

the compressor operation,

the compressor stops

operating immediately and

the indoor unit is under the

Thermo-OFF condition.

•

When DSW1-4 is OFF, the

compressor starts to operate

after the cancellation of the

3-minute guard.

•

Do not turn ON and OFF the

compressor frequently

Set DSW1-1 ON

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Search results

Summary of Contents for RAS-(2-3)HVRN(S)(2)

Reviews:

Related manuals for RAS-(2-3)HVRN(S)(2)

Brands by name

Popular brands

Hitachi RAS-(2-3)HVRN(S)(2), Service Manual

Search results

Summary of Contents for RAS-(2-3)HVRN(S)(2)

Reviews:

Related manuals for RAS-(2-3)HVRN(S)(2)

Brands by name

Popular brands