manualshive.com logo in svg

Hitachi RAS-(2-3)HVRN(S)(2), Service Manual

The Hitachi RAS-(2-3)HVRN(S)(2) Service Manual is a comprehensive user guide for this advanced air conditioner model. With detailed instructions and illustrations, this manual is essential for troubleshooting, maintenance, and optimal utilization of the product. Download for free from manualshive.com and unlock the full potential of your Hitachi air conditioner.

Share
Download
background image

4  Electrical Wiring

92

SMGB0064 rev.0 - 08/2011

DSW5: Transmission setting of end terminal resistance

•  Before shipment, No. 1 pin of DSW5 is set at ON.
•  In case of having 2 or more outdoor units connected to the same H-link, set for the second unit the pin number 1 of 

DSW5 at OFF.

•  If only one outdoor unit is used, no setting is required.

Function

Setting position

Setting before shipment

Cancellation

DSW6: Power source setting

Function

(2/2.5/3) HP

(4/5/6) HP

(8/10) HP

230V
(Setting before shipment)

400V
(setting before shipment)

Jumper lead setting (JP1~6)

Setting before shipment:

JP1

JP2

JP3

JP4

JP5

JP6

1

0

0

1

1

1

N O T E

• 

0: Open

• 

1: Short circuit

 
The function selection using the jumper lead setting is shown in the table below.

Setting

Function

Details

JP1

Not used

—

JP2

Not used

—

JP3

Not used

—

JP4

Fixing for Cooling Only

When JP4 is set to “open”, operation mode is fixed for cooling. Thermo-ON is avai-

lable only by “COOL” or “DRY” mode at indoor unit.

JP5

Not used

—

JP5

R407C pipes

When JP6 is set to “open”, existing piping system control is available. High pressu-

re control is performed depending on existing piping strength.

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RAS-(2-3)HVRN(S)(2)

Fedders Room Air Conditioners Important Safety Instructions Manual preview
Room Air Conditioners
Brand: Fedders Pages: 12
Fellowes AeraMax DX55 Quick Start Manual preview
AeraMax DX55
Brand: Fellowes Pages: 8
ICP DELUXE HIGH WALL MINI SPLIT Ower'S Manual preview
DELUXE HIGH WALL MINI SPLIT
Brand: ICP Pages: 26
Haier HBU-28CF03 Installation Instructions Manual preview
HBU-28CF03
Brand: Haier Pages: 14
Haier HWR05XC9 Instrucciones De Operación preview
HWR05XC9
Brand: Haier Pages: 20
Haier HWF05XC7 Manual De Usuario preview
HWF05XC7
Brand: Haier Pages: 20
Haier HW-07LM03 Operation Manual preview
HW-07LM03
Brand: Haier Pages: 12
Haier HSU18VH7 Manual preview
HSU18VH7
Brand: Haier Pages: 36
Haier HWE18VCN User & Care Manual preview
HWE18VCN
Brand: Haier Pages: 100
Haier HSU-24C03 Manual preview
HSU-24C03
Brand: Haier Pages: 24
Haier H2SM- Manual preview
H2SM-
Brand: Haier Pages: 19
Haier H2SM- Operating Manual preview
H2SM-
Brand: Haier Pages: 99
Haier ESA3156 - ANNEXE 221 Manual preview
ESA3156 - ANNEXE 221
Brand: Haier Pages: 25
Haier ESA3159 User Manual preview
ESA3159
Brand: Haier Pages: 26
Haier ESA3159 Manuel preview
ESA3159
Brand: Haier Pages: 25
Haier AU222XHBAA Manual preview
AU222XHBAA
Brand: Haier Pages: 19
Haier HSU-22H03/R2 Manual preview
HSU-22H03/R2
Brand: Haier Pages: 25
Haier ESA3067 - annexe 1 Manuel preview
ESA3067 - annexe 1
Brand: Haier Pages: 22

Brands by name

Popular brands

Load more brands