Hitachi RAS-(2-3)HVRN(S)(2) Service Manual Download Page 112 | Manualshive

Page: 112 / 488

background image

4 Electrical Wiring

102

SMGB0064 rev.0 - 08/2011

The following settings are not available:

N O T E

•

It is not possible to connect diferent indoor units from diferent systems with the same remote control, once the

remote control function wiring has been selected not to be used.

•

All optional units connected to CN3 can only be used with master unit with remote control connected to it.

Application

The H-LINK II wiring system requires only two transmission cables that connect each indoor unit and the outdoor unit for
up to 64 refrigerant cycles. This wiring system also requires the connect wires for all the indoor units and all the outdoor
units in series. You can apply this H-LINK II system to following models:

Indoor Unit

Outdoor Unit

RCI(M)

RAS-(3-12)H(V)RNM2(E)

RAS-(2-10)H(V)RN(S)(2)(E)

RDC

RPI(M)

RPK
RPF

RPFI

RPC

H-LINK II features

• It is possible to control up to 160 indoor units (64 groups of indoor units) with only one control panel (using the PSC-64S

controller). It is possible to control up to 200 units (indoor unit, outdoor unit and central control).

•  The total wiring length is remarkably reduced.
•  Only one (1) connection is required for the wiring between the indoor unit and the outdoor unit.
•  Easy wiring connection to the central control panels.

Example of an H-LINK II system:

A refrigerant cycle

Outdoor unit

Indoor units

Transmission cables

Refrigerant piping

«
...
110
111
112
113
114
...
»

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RAS-(2-3)HVRN(S)(2)

Brand: Samsung Pages: 10

Brand: Samsung Pages: 74

Brand: Haier Pages: 4

Brand: Haier Pages: 8

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 127

Brand: Daikin Pages: 19

Brand: Prem-I-Air Pages: 15

Brand: Airwell Pages: 32

Brand: Bard Pages: 137

Brand: Technibel Pages: 27

Pro-Kool M-PROK142

Brand: Schaefer Pages: 16

Brand: Crosley Pages: 8

Brand: Celuplast Pages: 8

Brand: Ivation Pages: 3

Brand: Clatronic Pages: 54

Brand: Haier Pages: 537

Brand: Daikin Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands