Hitachi RAS-(2-3)HVRN(S)(2) Service Manual Download Page 274

Page: 274 / 488

8 Troubleshooting

264

SMGB0064 rev.0 - 08/2011

Alarm code

Overcurrent protection activation for IVX series

Restart operation.

Does it trip soon?

Yes

Turn OFF power and

disconnect U, V, W from

compressor terminals.

Turn ON #1 of DSW1 on PCB2

(IPM or dipIPM) and restart.

Does it trip? *1)

Is there any cause of

instantaneous voltage

decrease?

Check the

compressor.

Check the power

source capacity.

Replace the PCB2

(IPM or dipIPM). *1)

Yes

Yes, it

trips

It trips

immediately

In case of 380-415V/50Hz

Is the power supply voltage 380V ±10% or 415V ±10% ?

In case of 220~240V/50Hz:

Is the power supply voltage 230V ±10%?

Yes

In case of 380-415V/50Hz:

Is the power supply voltage 323V during operation?

In case of 220~240V/50Hz:

Is the power supply voltage 187V during operation?

Yes

Is it 170V (single phase) or 340V (3 phases) or more

during operation when other devices are operating?

Yes

Is the compressor running current the same as rated

current?

Yes

Check the capacity and

wiring of the power source.

Check the fan.

Check for clogging at

heat exchanger.

Check the stop valves

and expansion valve.

Check the compressor.

Restart expansion

valve.

Charge refrigerant

correctly.

Restart operation after

applying current.

Is current applying to

crankcase heater?

Is refrigerant charged

excessively?

Yes

Is lock of indoor expansion valve

opened at cooling operation?

Is lock of outdoor expansion valve

opened at heating operation?

Yes

Is pressure excessively

high?

Yes

It trips after a

certain period

N O T E

*1) Perform the high voltage discharge work by referring to section

Procedure of checking other main parts for ES

Series

, see on page 312

before checking and replacing the inverter PCB.

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Search results

Summary of Contents for RAS-(2-3)HVRN(S)(2)

Reviews:

Related manuals for RAS-(2-3)HVRN(S)(2)

Brands by name

Popular brands

Hitachi RAS-(2-3)HVRN(S)(2), Service Manual

Search results

Summary of Contents for RAS-(2-3)HVRN(S)(2)

Reviews:

Related manuals for RAS-(2-3)HVRN(S)(2)

Brands by name

Popular brands