manualshive.com logo in svg

Hitachi RAS-(2-3)HVRN(S)(2), Service Manual

The Hitachi RAS-(2-3)HVRN(S)(2) Service Manual is a comprehensive user guide for this advanced air conditioner model. With detailed instructions and illustrations, this manual is essential for troubleshooting, maintenance, and optimal utilization of the product. Download for free from manualshive.com and unlock the full potential of your Hitachi air conditioner.

Share
Download
background image

10  Servicing

416

SMGB0064 rev.0 - 08/2011

1. Electrical box.
2. Upper cover.
3. Refrigerant amount controller.
4. Pressure switch for control.
5. High pressure switch.
6. Blazing.
7. Discharge pipe.

1

2

3

4

4

5

5

6

6

7

 







Opening electrical box (P plate)

1 

Remove the service cover following 

Removing service cover

, see on page 408

 in this chapter.

2 

Remove six (5) screws which fix the electrical box and open the P plate turning counter clockwise approximately 90°.

•  Check that the LED201 (red) on the inverter PCB (PCB2) is OFF when opening P-mounting plate.

1. P Plate.
2. Upper cover.
3. Screw.
4. Two (2) screws.

1

2

3

4

4

 

D A N G E R

• 

DO NOT touch electrical components while the LED201 (Red) is ON to avoid electrical shock. Wait until the 

LED turns off.

 







Removing four-way valve coil

1 

Remove the service cover following 

Removing service cover

, see on page 408

.

2 

Open the P plate following 

Opening electrical box (P plate)

, see on page 416

.

3 

Disconnect the PCN6 connector on the control PCB of the electrical box.

4 

Remove one (1) fixing screw to remove the 4-way valve coil.

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RAS-(2-3)HVRN(S)(2)

Samsung AW0700 Manual De Instrucciones preview
AW0700
Brand: Samsung Pages: 12
Samsung MC18AC2-09 Owner'S Instructions Manual preview
MC18AC2-09
Brand: Samsung Pages: 24
Samsung AM080FXWANR Service Manual preview
AM080FXWANR
Brand: Samsung Pages: 295
Samsung AW07A(G)2NBA/DE/EA Manual De Instrucciones preview
AW07A(G)2NBA/DE/EA
Brand: Samsung Pages: 16
Airwell May series Installation Manual preview
May series
Brand: Airwell Pages: 6
Armstrong Air 4SCU 16LS Series Installation And Maintenance Instructions Manual preview
4SCU 16LS Series
Brand: Armstrong Air Pages: 32
York 3 PH Installation Instruction preview
3 PH
Brand: York Pages: 12
GE AEH06LV Owner'S Manual And Installation Instructions preview
AEH06LV
Brand: GE Pages: 28
Daikin Altherma EPGA16DAV3 Installer'S Reference Manual preview
Altherma EPGA16DAV3
Brand: Daikin Pages: 100
Klimaire KSWM009-C113 Service Manual preview
KSWM009-C113
Brand: Klimaire Pages: 51
Daikin MXS-E Technical Data Manual preview
MXS-E
Brand: Daikin Pages: 43
BEEWAIR BW60L Operating Manual preview
BW60L
Brand: BEEWAIR Pages: 20
Maytag 23-11-2228N-004 User Manual preview
23-11-2228N-004
Brand: Maytag Pages: 24
Kampmann KA-520 XL Quick Start Manual preview
KA-520 XL
Brand: Kampmann Pages: 3
ClimateRight CR-5000-AC Owner'S Manual preview
CR-5000-AC
Brand: ClimateRight Pages: 10
SPT WA-1511S User Manual preview
WA-1511S
Brand: SPT Pages: 24
Hisense AVW-38UCSC Installation & Maintenance Manual preview
AVW-38UCSC
Brand: Hisense Pages: 42
Olimpia splendid SILENCLIMA Instructions For Installation, Use And Maintenance Manual preview
SILENCLIMA
Brand: Olimpia splendid Pages: 28

Brands by name

Popular brands

Load more brands