Hitachi RAS-(2-3)HVRN(S)(2) Service Manual Download Page 287 | Manualshive

Page: 287 / 488

background image

8 Troubleshooting

277

SMGB0064 rev.0 - 08/2011

8

Alarm code

57

Abnormality of fan motor protection (DC fan motor) for IVX series

• The RUN LED flickers and “ALARM” is displayed on the remote control switch.
• The unit number, the alarm code and the unit code are alternately displayed on the set temperature section. The unit

number and the alarm code are displayed on the display of the outdoor unit PCB.

-

This alarm is indicated when the revolution pulse output from the fan motor is 10 rpm or less and the
reverse revolution signal is detected. The fan motor is stopped once, and restarted after 10 seconds.

If it occurs more than 10 times in 30 minutes, this alarm is indicated. The abnormality occurs when the fan motor
is stopped.

Yes

This alarm is indicated due

to detected overcurrent by

the contrary wind. This is

normal.

Does the motor run?

Remove the foreign matter.

Does the fan stop by the foreign

matter?

Check to remove the connector connection of CN15 (on PCB1)

and CN201, CN202, PCN201, PCN203 (on PCB5).

Faulty

Restart operation

No

Alarm code is not indicated

Yes

No

Are the connectors abnormal?

Connect it correctly.

Restart operation

Does the motor run?

This is normal

Replace the fan motor

Restart operation

Does the motor run?

Yes

Good

This is normal

Yes

No

Alarm code is not indicated

Replace the PCB1

No

N O T E

•

In the case that the fan motor does not run even the PCB1 is replaced, replace PCB5.

•

Check to ensure that DC Fan Motor is checked according to the item

Procedure of checking other main parts

for ES Series

, see on page 312

.

«
...
285
286
287
288
289
...
»

Summary of Contents for RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RAS-(2-3)HVRN(S)(2)

Brand: Magnavox Pages: 19

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 18

Brand: Panasonic Pages: 14

Brand: Panasonic Pages: 112

Brand: York Pages: 32

Therapy Air Smart TAS-100

Brand: Zepter Pages: 9

Super Multi NX FHQ35BVV1B

Brand: Daikin Pages: 19

Brand: York Pages: 25

TC 200 SPLIT Series

Brand: Gorenje Pages: 40

Brand: York Pages: 30

Brand: DUSTER Pages: 8

Brand: iGenix Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands