Hioki DSM-8542, Instruction Manual, Page: 55 / 140

45
[Notices]
1. The measuring time sometimes lengthens the self-calibration execution time
(about 2s) when auto execute is on.
2. Auto self-calibration cannot be performed even when auto execute is set to
ON if sequential measurement is ON.
5.2.14 Setting measuring voltage source ([SETUP], POWR)
(1) Press the [F4] POWR (POWER) key on the Operating Environment Setting
screen.
The screen will change to the Current Limit Value Setting screen. (See Fig.
5.15)
Ｐ Ｏ Ｗ Ｅ Ｒ Ｓ Ｏ Ｕ Ｒ Ｃ Ｅ Ｓ Ｅ Ｌ Ｓ Ｅ Ｃ Ｔ
Ｍ Ｅ Ａ Ｓ Ｃ Ｈ ： １ ／ ２ ／ ３ ／ ４
Ｃ Ｈ １ － ２ ： Ｐ Ａ ／ Ｐ Ｂ
Ｃ Ｈ ３ － ４ ： Ｐ Ａ ／ Ｐ Ｂ
Ｆ Ｉ Ｌ Ｔ Ｅ Ｒ ： Ｏ Ｆ Ｆ ／ Ｏ Ｎ
Ｃ Ｕ Ｒ Ｌ Ｉ Ｍ ： ０ ／ ５ ／ １ ０ ／ ２ ５ ／ ５ ０ ｍ Ａ
Ｃ Ｕ Ｒ Ｌ Ｉ Ｃ ： ０ ／ ５ ／ １ ０ ／ ２ ５ ／ ５ ０ ｍ Ａ
Ｏ Ｎ Ｏ Ｆ Ｆ
Fig. 5.15 Current Limit Value Setting Screen
The following items are set: Measuring channel (measurement ON/OFF),
PSU-8541 measuring current, charging current and power noise filter function,
CH1-2: PA/PB, CH3-4: PA/PB to notify internal connection of PSU-8541 to the
DSM-8542.
Select a set item operating the [
▲
], [
▼
], [
►
] and [
◄
] keys.
The selected item will be highlighted on the screen.
Press the [ENTER] key to return to the Measurement screen after completing
setting. The following settings for internal connection are important settings.
CH1-2: PA/PB
CH3-4: PA/PB
Be certain to set them to correspond to PSU-8541 1:1. Set the measuring
channels operating the [
►
] and [
◄
] keys like [F4] ON and [F5] OFF.
(2) Setting measuring current limit value
Set a measuring current limit value in “CURL IM: 0/5/10/25/50mA.”
This current limit sets a current limit value for the current source supplied by
PSU-8541 to the DSM-8542. A value can be set for four channels
simultaneously.
(3) Setting charging current limit value
Set a current value for the charging side in “CURL IC: 0/5/10/25/50mA.”
This current limit sets a current limit value for the current source to charge a
sample capacitor by PSU-8541 for preliminary charging before measurement.
A value can be set for 20 channels simultaneously.
The side mark “CHARGE ON” will go off if this setting is “0.” The current
capacity of PSU-8541 is specified in Table 5.8.