1-27
# Configure the suppression time of physical-link-state changes on GigabitEthernet 1/0/1 and
GigabitEthernet 1/0/2 as zero, disable STP, configure the two ports as trunk ports, remove them from
VLAN 1, and assign them to VLAN 10 and VLAN 20, and configure them to trust the 802.1p precedence
of the received packets.
[DeviceB] interface gigabitethernet 1/0/1
[DeviceB-GigabitEthernet1/0/1] link-delay 0
[DeviceB-GigabitEthernet1/0/1] undo stp enable
[DeviceB-GigabitEthernet1/0/1] port link-type trunk
[DeviceB-GigabitEthernet1/0/1] undo port trunk permit vlan 1
[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 10 20
[DeviceB-GigabitEthernet1/0/1] qos trust dot1p
[DeviceB-GigabitEthernet1/0/1] quit
[DeviceB] interface gigabitethernet 1/0/2
[DeviceB-GigabitEthernet1/0/2] link-delay 0
[DeviceB-GigabitEthernet1/0/2] undo stp enable
[DeviceB-GigabitEthernet1/0/2] port link-type trunk
[DeviceB-GigabitEthernet1/0/2] undo port trunk permit vlan 1
[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 10 20
[DeviceB-GigabitEthernet1/0/2] qos trust dot1p
[DeviceB-GigabitEthernet1/0/2] quit
# Configure the suppression time of physical-link-state changes on GigabitEthernet 1/0/3 as zero,
disable STP, configure the port as a trunk port, remove it from VLAN 1, and assign it to VLAN 20, and
configure it to trust the 802.1p precedence of the received packets.
[DeviceB] interface gigabitethernet 1/0/3
[DeviceB-GigabitEthernet1/0/3] link-delay 0
[DeviceB-GigabitEthernet1/0/3] undo stp enable
[DeviceB-GigabitEthernet1/0/3] port link-type trunk
[DeviceB-GigabitEthernet1/0/3] undo port trunk permit vlan 1
[DeviceB-GigabitEthernet1/0/3] port trunk permit vlan 20
[DeviceB-GigabitEthernet1/0/3] qos trust dot1p
[DeviceB-GigabitEthernet1/0/3] quit
# Configure the suppression time of physical-link-state changes on GigabitEthernet 1/0/4 as zero,
disable STP, configure the port as a trunk port, remove it from VLAN 1, and assign it to VLAN 10, and
configure it to trust the 802.1p precedence of the received packets.
[DeviceB] interface gigabitethernet 1/0/4
[DeviceB-GigabitEthernet1/0/4] link-delay 0
[DeviceB-GigabitEthernet1/0/4] undo stp enable
[DeviceB-GigabitEthernet1/0/4] port link-type trunk
[DeviceB-GigabitEthernet1/0/4] undo port trunk permit vlan 1
[DeviceB-GigabitEthernet1/0/4] port trunk permit vlan 10
[DeviceB-GigabitEthernet1/0/4] qos trust dot1p
[DeviceB-GigabitEthernet1/0/4] quit
# Create RRPP domain 1, configure VLAN 100 as the primary control VLAN of RRPP domain 1, and
configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.
[DeviceB] rrpp domain 1
[DeviceB-rrpp-domain1] control-vlan 100
Summary of Contents for S5500-SI Series
