golmar NEXA Series User Manual Download

Page: 101 / 146

DESCRIPTION OF THE DOOR PANEL

101

Description of the Nexa modular door panel:

AUDIO AND VIDEO DOOR ENTRY SYSTEM - CODED PANEL WITH DISPLAY

Sound module

EL63 GTWIN

Access control module

N3301/AL ,

coded module and access control.

video door entry system with colour television camera,

(non-polarised 2-wires bus).

Door panel component assembly drawing.

Aluminium panel

Electronic modules

Frame modules

Embedding boxes

Description of the door panel.

Side profile

Door panel joining bar

Door panel joining bar: Enables 2 door panels to be joined.

Display module

N3403,

display module.

NEXA Bus link hose (length 50 cm).

To connect the EL632 EL642

module

to the N3301/AL coded

Plus

or EL632/EL642 R5

module and the N3403 display module.

Grille modules

N1000/AL
N1110/AL 1P.
N2220/AL 2P.

Clip-on covers: 60xx

Blank module

: N3000/AL

Nexa module separator

(x2)

Fixing screws for clip-on covers

(x8)

Side profile

(x2)

Fixing screws for embedding box

(x4)

Display module

N3403/AL

Coded module

N3301/AL

Summary of Contents for NEXA Series



















































































































































Search results

Summary of Contents for NEXA Series

Reviews:

Related manuals for NEXA Series

Brands by name

Popular brands

golmar NEXA Series, User Manual

Search results

Summary of Contents for NEXA Series

Reviews:

Related manuals for NEXA Series

Brands by name

Popular brands