golmar NEXA Series User Manual Download

Page: 100 / 146

DESCRIPTION OF THE DOOR PANEL

100

Description of the Nexa modular door panel:

AUDIO AND VIDEO DOOR ENTRY SYSTEM - CODED PANEL WITH DISPLAY

Sound modules

EL63 PLUS P/T

EL642/PLUS
EL632 R5 P/T
EL642/R5

Access control module

N3301/AL ,

coded module and access control.

video door entry system with colour television camera, 3 wires + COAX.

Door panel component assembly drawing.

Aluminium panel

Electronic modules

Frame modules

Embedding boxes

Description of the door panel.

Grille modules:

N1000/AL
N1110/AL 1P.
N2220/AL 2P.

Clip-on covers: 60xx

Display module:

N3403/AL

Nexa module separator (x2)

Fixing screws for clip-on covers (x4)

Side profile (x2)

Side profile

Door panel joining bar

Fixing screws for embedding box (x2)

Door panel joining bar: Enables 2 door panels to be joined.

audio door entry system, 4 common wires.

video door entry system with colour television camera, 5 common wires.

audio door entry system, 5 common wires.

Display module

N3403,

display module.

Coded module

N3301/AL

NEXA Bus link hose (length 50 cm).

To connect the EL632 EL642

module

to the N3301/AL coded

Plus

or EL632/EL642 R5

module and the N3403 display module.

Summary of Contents for NEXA Series



















































































































































Search results

Summary of Contents for NEXA Series

Reviews:

Related manuals for NEXA Series

Brands by name

Popular brands

golmar NEXA Series, User Manual

Search results

Summary of Contents for NEXA Series

Reviews:

Related manuals for NEXA Series

Brands by name

Popular brands