manualshive.com logo in svg

GMC 2000 Safari, Owner'S Manual

The GMC 2000 Safari Owner's Manual is a comprehensive guide that provides step-by-step instructions and valuable information on operating and maintaining your vehicle. With a user-friendly format, this manual is available for free download at manualshive.com, allowing you to access it conveniently and keep your Safari running smoothly.

Share
Download
background image

3-29

Unlocking the Theft

-

Deterrent Feature After a

Power Loss

Enter your secret code as follows; pause no more than
15 seconds between steps:

1. Turn the ignition on. LOC will appear on the display.

2. Press MN and 000 will appear on the display.

3. Press MN again to make the last two digits agree

with your code.

4. Press HR to make the first one or two digits agree

with your code.

5. Press AM

-

FM after you have confirmed that the

code matches the secret code you have written down.
The display will show SEC, indicating the radio is
now operable and secure.

If you enter the wrong code eight times, INOP will
appear on the display. You will have to wait an hour
with the ignition on before you can try again. When you
try again, you will only have three chances to enter the
correct code before INOP appears.

If you lose or forget your code, contact your dealer.

Disabling the Theft

-

Deterrent Feature

Enter your secret code as follows; pause no more than
15 seconds between steps:

1. Turn the ignition to ACCESSORY or RUN.

2. Turn the radio off.

3. Press the 1 and 4 buttons together. Hold them down

until SEC shows on the display.

4. Press MN and 000 will appear on the display.

5. Press MN again to make the last two digits agree

with your code.

6. Press HR to make the first one or two digits agree

with your code.

7. Press AM

-

FM after you have confirmed that the

code matches the secret code you have written down.
The display will show 

---

, indicating that the radio is

no longer secured.

If the code entered is incorrect, SEC will appear on the
display. The radio will remain secured until the correct
code is entered.

Summary of Contents for 2000 Safari








































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Safari

Harken Hoister SUP Manual preview
SUP
Brand: Harken Hoister Pages: 12
Yamaha Raptor Instruction Supplement preview
Raptor
Brand: Yamaha Pages: 2
Q'STRAINT QLK-150 Installation Instructions Manual preview
QLK-150
Brand: Q'STRAINT Pages: 10
TATA Motors Safari Owner'S Manual & Service Book preview
Safari
Brand: TATA Motors Pages: 161
TAUBENREUTHER 16 - 590 Fitting Instructions Manual preview
16 - 590
Brand: TAUBENREUTHER Pages: 11
Yakima SKYBOX Series Manual preview
SKYBOX Series
Brand: Yakima Pages: 15
Quadratec Brute Strength 12057.0271 Installation Manual preview
Brute Strength 12057.0271
Brand: Quadratec Pages: 6
TATA Motors Indigo MANZA QUADRAJET 90 Owner'S Manual & Service Book preview
Indigo MANZA QUADRAJET 90
Brand: TATA Motors Pages: 10
FALCON RIDGE BC-3400-FC05 Instructions For Installation And Care preview
BC-3400-FC05
Brand: FALCON RIDGE Pages: 7
Volvo 2004 C70 HPT User Manual preview
2004 C70 HPT
Brand: Volvo Pages: 30
Jaeger 21360508 Fitting Instructions Manual preview
21360508
Brand: Jaeger Pages: 13
Lexus HS 250h Vehicle Dismantling Manual preview
HS 250h
Brand: Lexus Pages: 34
Toyota 86 2020 Quick Reference Manual preview
86 2020
Brand: Toyota Pages: 32
Paccar PACCHARGE AC20 Installation Manual preview
PACCHARGE AC20
Brand: Paccar Pages: 63
Curt Manufacturing 58963 Installation Manual preview
58963
Brand: Curt Manufacturing Pages: 4
Whispbar K559W Fitting Instructions Manual preview
K559W
Brand: Whispbar Pages: 112
Crux RVCFD-79 Manual preview
RVCFD-79
Brand: Crux Pages: 10
Buick 2014 LaCrosse Manual preview
2014 LaCrosse
Brand: Buick Pages: 112

Brands by name

Popular brands

Load more brands