manualshive.com logo in svg

GMC 2000 Safari, Owner'S Manual

The GMC 2000 Safari Owner's Manual is a comprehensive guide that provides step-by-step instructions and valuable information on operating and maintaining your vehicle. With a user-friendly format, this manual is available for free download at manualshive.com, allowing you to access it conveniently and keep your Safari running smoothly.

Share
Download
background image

6-22

Checking the Fluid Level

Prepare your vehicle as follows:
D Park your vehicle on a level place. Keep the 

engine running.

D With the parking brake applied, place the shift lever

in PARK (P).

D With your foot on the brake pedal, move the shift

lever through each gear range, pausing for about
three seconds in each range. Then, position the shift
lever in PARK (P).

D Let the engine run at idle for three minutes or more.

Then, without shutting off the engine, follow 
these steps:

1. The transmission dipstick has a red handle and is

located near the center of the engine compartment
behind the air cleaner. Flip the handle up and then
pull out the dipstick and wipe it with a clean rag or
paper towel.

2. Push it back in all the way, wait three seconds and

then pull it back out again.

Summary of Contents for 2000 Safari








































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Safari

Pacbrake 10475 Installation Manual preview
10475
Brand: Pacbrake Pages: 9
VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Brand: VEAP SHIELD UNITED Pages: 3
Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Brand: Eaton Pages: 65
Zavoli Bora Technical Instructions And Installation Manual preview
Bora
Brand: Zavoli Pages: 26
Jacob Jensen Electronic Parking Disc 3 Quick Manual preview
Electronic Parking Disc 3
Brand: Jacob Jensen Pages: 2
Yakima K1005 Instructions Manual preview
K1005
Brand: Yakima Pages: 12
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Brand: PUTCO Pages: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Brand: Westfalia Pages: 18
Honda 2004 S2000 Owner'S Manual preview
2004 S2000
Brand: Honda Pages: 208
Webasto CC4E Installation And Service Instructions Manual preview
CC4E
Brand: Webasto Pages: 34
Audiovox AA-BAT Programming Manual preview
AA-BAT
Brand: Audiovox Pages: 3
Victory 4x4 VRKCAP Install Instructions Manual preview
VRKCAP
Brand: Victory 4x4 Pages: 9
ZAPTEC ZapCharger Portable C1 User Manual preview
ZapCharger Portable C1
Brand: ZAPTEC Pages: 20
Butts of Bawtry TBT4700 Quick Start Manual preview
TBT4700
Brand: Butts of Bawtry Pages: 2
Belkin LineCast Auto FM User Manual preview
LineCast Auto FM
Brand: Belkin Pages: 15
Rover 75 Saloon Owner'S Handbook Manual preview
75 Saloon
Brand: Rover Pages: 285
Xpresskit 20110601 Installation Manual preview
20110601
Brand: Xpresskit Pages: 12
Kuda 293950 Installation Instruction preview
293950
Brand: Kuda Pages: 3

Brands by name

Popular brands

Load more brands