manualshive.com logo in svg

GMC 2000 Safari, Owner'S Manual

The GMC 2000 Safari Owner's Manual is a comprehensive guide that provides step-by-step instructions and valuable information on operating and maintaining your vehicle. With a user-friendly format, this manual is available for free download at manualshive.com, allowing you to access it conveniently and keep your Safari running smoothly.

Share
Download
background image

3-7

Your vehicle has air vents near the center and on the
sides of the instrument panel that allow you to adjust the
direction and the amount of airflow inside the vehicle.
Move the dial on the vent up or down to direct airflow
to your preference. Increase or reduce the amount of
airflow by opening and closing the louvers. The vents
rotate to direct the airflow from side to side.

When you close a vent, it will increase the flow of air
coming out of any vents that are open.

If you have rear heating or rear air conditioning, you
will have adjustable vents in the rear of the vehicle to
help direct the airflow. The rear air conditioning vents
are located in the headliner at the rear of the vehicle.
The rear heating vents are located next to the second and
third seat on the driver’s side of the vehicle, near the
floor. You can move the vents to direct the flow of air, or
close the vents altogether. When you close a vent, it will
increase the flow of air coming out of any vents that 
are open.

Ventilation Tips

D Keep the hood and front air inlet free of ice, snow or

any other obstruction (such as leaves). The heater
and defroster will work far better, reducing the
chance of fogging the inside of your windows.

D When you enter a vehicle in cold weather, turn the

blower fan to HIGH for a few moments before
driving off. This helps clear the intake ducts of snow
and moisture, and reduces the chance of fogging the
inside of your windows.

D Keep the air path under the front seats clear of

objects. This helps air to circulate throughout 
your vehicle.

Summary of Contents for 2000 Safari








































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Safari

iDataLink Maestro Installation Manual preview
Maestro
Brand: iDataLink Pages: 9
Vauxhall Meriva Quick Reference Manual preview
Meriva
Brand: Vauxhall Pages: 2
Vauxhall Ampera Quick Reference Manual preview
Ampera
Brand: Vauxhall Pages: 2
Vauxhall 2012 Agila Quick Reference Manual preview
2012 Agila
Brand: Vauxhall Pages: 2
Vauxhall 2013 Mokka Owner'S Manual preview
2013 Mokka
Brand: Vauxhall Pages: 209
VBC Racing WildFire Instruction Manual preview
WildFire
Brand: VBC Racing Pages: 34
Vauxhall 2013 Corsa Infotainment system Quick Reference Manual preview
2013 Corsa Infotainment system
Brand: Vauxhall Pages: 2
Vauxhall 2010 Astra Quick Reference Manual preview
2010 Astra
Brand: Vauxhall Pages: 2
Vauxhall Antara Owner'S Manual preview
Antara
Brand: Vauxhall Pages: 236
Uebler F42 Mounting And Operating Instructions preview
F42
Brand: Uebler Pages: 18
Jeep Cherokee 16 1982 Technical & Service Manual preview
Cherokee 16 1982
Brand: Jeep Pages: 1311
APS Auto Parts Specialist iBoard IB-ZK406 Installation Instructions preview
iBoard IB-ZK406
Brand: APS Auto Parts Specialist Pages: 3
Dometic PERFECTVIEW CAM80AHD Installation And Operating Manual preview
PERFECTVIEW CAM80AHD
Brand: Dometic Pages: 196
EUFAB 11556 Operating Instructions Manual preview
11556
Brand: EUFAB Pages: 52
GMC Envoy XUV 2004 Getting To Know Manual preview
Envoy XUV 2004
Brand: GMC Pages: 20
WABCO OnSide MM16167 Maintenance Manual preview
OnSide MM16167
Brand: WABCO Pages: 52
Kia Sorento Owner'S Manual preview
Sorento
Brand: Kia Pages: 51
Anker Technology Roav VIVA Owner'S Manual preview
Roav VIVA
Brand: Anker Technology Pages: 8

Brands by name

Popular brands

Load more brands