GMC 2000 Safari Owner'S Manual Download Page 248 | Manualshive

Page: 248 / 391

background image

5-27

CAUTION:

Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips off the jack, you
could be badly injured or killed. Never get under
a vehicle when it is supported only by a jack.

CAUTION:

Raising your vehicle with the jack improperly
positioned can damage the vehicle and even make
the vehicle fall. To help avoid personal injury
and vehicle damage, be sure to fit the jack lift
head into the proper location before raising
the vehicle.

7. Raise the vehicle by turning the ratchet clockwise.

Make sure the UP mark faces you. Raise the vehicle
far enough off the ground so there is enough room
for the spare tire to fit.

8. Remove all the wheel nuts and take off the flat tire.

«
...
246
247
248
249
250
...
»

Summary of Contents for 2000 Safari








































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Safari

Brand: LaserTrack Pages: 12

Yamaha Rhino 660

Brand: Yamaha Pages: 3

Brand: Wagan Pages: 8

Brand: Thermo King Pages: 2

Brand: Volvo Pages: 188

Brand: Hama Pages: 75

2016 Sandero Stepway

Brand: Renault Pages: 183

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: Prorack Pages: 15

Brand: Huf Pages: 6

Brand: Mopar Pages: 18

Brand: iQOS Pages: 4

Brand: Subaru Pages: 2

Brand: Husky Pages: 8

Brand: RAWLINK Pages: 25

Brand: Connects2 Pages: 2

2002 Civic Hatchback

Brand: Honda Pages: 119

BLADE-AL-TL5-EN

Brand: Automotive Data Solutions Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands