GMC 2000 Safari Owner'S Manual Download Page 240 | Manualshive

Page: 240 / 391

background image

5-19

Changing a Flat Tire

If a tire goes flat, avoid further tire and wheel damage
by driving slowly to a level place. Turn on your hazard
warning flashers.

CAUTION:

Changing a tire can cause an injury. The vehicle
can slip off the jack and roll over you or other
people. You and they could be badly injured.
Find a level place to change your tire. To help
prevent the vehicle from moving:

1. Set the parking brake firmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine.
4. Put the wheel blocks at the front and

rear of the tire farthest away from the
one being changed. That would be the
tire on the other side of the vehicle, at
the opposite end.

The following steps will tell you how to use the jack and
change a tire.

«
...
238
239
240
241
242
...
»

Summary of Contents for 2000 Safari








































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Safari

Brand: Saab Pages: 75

Brand: IAG Pages: 3

Brand: Alpine Pages: 2

Brand: Whispbar Pages: 15

Brand: TrailFX Pages: 6

Brand: FORM FIT Pages: 2

Edge Flush Rail

Brand: Thule Pages: 12

Brand: Safe Fleet Pages: 38

Brand: AA Products Pages: 4

Brand: STC Pages: 6

Brand: Jeep Pages: 1528

Brand: Mini Pages: 20

Brand: Right Weigh Pages: 16

1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P

Brand: Havis-Shields Pages: 1

Brand: Cadillac Pages: 20

Brand: Prorack Pages: 15

Brand: Needit Pages: 2

KIT ParkingSensor 814

Brand: Gemini Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands