manualshive.com logo in svg

GMC 2000 Safari, Owner'S Manual

The GMC 2000 Safari Owner's Manual is a comprehensive guide that provides step-by-step instructions and valuable information on operating and maintaining your vehicle. With a user-friendly format, this manual is available for free download at manualshive.com, allowing you to access it conveniently and keep your Safari running smoothly.

Share
Download
background image

2-53

NOTICE:

Don’t put papers and other things that burn 
into your ashtrays. If you do, cigarettes or 
other smoking materials could set them on fire,
causing damage.

Sun Visors

To block out glare, you can swing down the visors. You
can also swing them from side to side. Your visors may
have an extension that can be pulled out for additional
glare protection and a strap for holding small items,
such as maps.

Visor Vanity Mirror (If Equipped)

Some visors have mirrors built in, with or without
lamps. Just lift the mirror cover on each visor to turn 
the lamps on, if you have them.

Accessory Power Outlets

You can plug auxiliary electrical equipment into accessory  
power outlets. Just pull up from the bottom of the door 
and follow the proper installation instructions that are
included with any electrical equipment that you install.

Two accessory power outlets are located on the
passenger’s side of the engine cover.

Another accessory power outlet is located on the driver’s
side behind the third row seating position, near the floor.

These circuits are protected by a fuse and have maximum
current levels.

NOTICE:

When using the accessory power outlets, maximum
electrical load must not exceed 25 amps. Always
turn off any electrical equipment when not in use.
Leaving electrical equipment on for extended
periods will drain your battery.

Summary of Contents for 2000 Safari








































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Safari

Vauxhall Cascada Quick Reference Manual preview
Cascada
Brand: Vauxhall Pages: 2
Taffio CH7102-FCX9 Quick Start Manual preview
CH7102-FCX9
Brand: Taffio Pages: 8
Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Brand: Ultra-tow Pages: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Brand: Mercedes-Benz Pages: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Brand: Menabo Pages: 8
Camtree G-51 Instruction Manual preview
G-51
Brand: Camtree Pages: 5
GMC Chevrolet Silverado 2500HD 2021 Owner'S Manual preview
Chevrolet Silverado 2500HD 2021
Brand: GMC Pages: 433
BMW E39/2 Installation Instructions Manual preview
E39/2
Brand: BMW Pages: 21
Pontiac 2004 Vibe Navigation System Owner'S Manual preview
2004 Vibe Navigation System
Brand: Pontiac Pages: 44
Cadillac 1999 DeVille Owner'S Manual preview
1999 DeVille
Brand: Cadillac Pages: 368
Luverne 205760 Installation Instructions preview
205760
Brand: Luverne Pages: 3
Navman B2+ User Manual preview
B2+
Brand: Navman Pages: 27
Firestone Ride-Rite Air Helper Springs 2173 Installation Instructions preview
Ride-Rite Air Helper Springs 2173
Brand: Firestone Pages: 4
I.D. Systems Vehicle Asset Communicator User Manual preview
Vehicle Asset Communicator
Brand: I.D. Systems Pages: 41
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Brand: Ranger design Pages: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Brand: AUTOTECH Pages: 1
Guidosimplex 907P User Manual preview
907P
Brand: Guidosimplex Pages: 8
S3 Power Sports S3193 Installation Instructions preview
S3193
Brand: S3 Power Sports Pages: 2

Brands by name

Popular brands

Load more brands