manualshive.com logo in svg

GMC 2000 Safari, Owner'S Manual

The GMC 2000 Safari Owner's Manual is a comprehensive guide that provides step-by-step instructions and valuable information on operating and maintaining your vehicle. With a user-friendly format, this manual is available for free download at manualshive.com, allowing you to access it conveniently and keep your Safari running smoothly.

Share
Download
background image

5-23

The tools you’ll be using include the jack (A), wheel
blocks (B), extension (C) and ratchet (D).

Removing the Wheel Covers

You will have to take off hub caps or wheel nut caps to
reach your wheel nuts.

Styled Steel Wheel Shown

If you have a standard steel wheel, carefully pry along
the edge of the hub cap until it comes off. Be careful, the
rim edges may be sharp. Don’t try to remove the hub
cap with your bare hands.

If you have the styled steel wheel or aluminum wheel
with plastic nut caps, loosen the plastic nut caps with the
ratchet and socket. Make sure the DOWN side 
faces you.

To remove the hub cap from the aluminum wheel
without plastic nut caps, fit the flat end of the extension
into the notch. Then, remove the center cap.

Summary of Contents for 2000 Safari








































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Safari

Federal Signal Corporation 7000 Assembly Instructions Manual preview
7000
Brand: Federal Signal Corporation Pages: 13
B-Speech B-Speech Prim Manual preview
B-Speech Prim
Brand: B-Speech Pages: 18
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Brand: Jeep Pages: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Brand: Jeep Pages: 80
Yakima K800 Instructions Manual preview
K800
Brand: Yakima Pages: 8
FORM FIT 1303 Installation Instructions preview
1303
Brand: FORM FIT Pages: 2
Honda 2010 Civic Sedan Owner'S Manual preview
2010 Civic Sedan
Brand: Honda Pages: 390
Mitsubishi MIrage 2019 Owner'S Handbook Manual preview
MIrage 2019
Brand: Mitsubishi Pages: 19
Belkin F8V9017 User Manual preview
F8V9017
Brand: Belkin Pages: 2
cam 40103 AL Mounting Instructions preview
40103 AL
Brand: cam Pages: 6
Softride 26428 Instructions preview
26428
Brand: Softride Pages: 4
ICON 91824E Installation Instructions preview
91824E
Brand: ICON Pages: 4
Mercedes-Benz A 150 Owner'S Manual preview
A 150
Brand: Mercedes-Benz Pages: 305
Volvo S90 TWIN ENGINE Owner'S Manual preview
S90 TWIN ENGINE
Brand: Volvo Pages: 662
Blue Ox BX2323 Installation Instructions Manual preview
BX2323
Brand: Blue Ox Pages: 9
Road Ranger ET 210207 Installation Instruction preview
ET 210207
Brand: Road Ranger Pages: 3
Volkswagen RCD550 Installation Manual preview
RCD550
Brand: Volkswagen Pages: 4
GMC 2004 Cadillac Warranty And Owner Assistance Information preview
2004 Cadillac
Brand: GMC Pages: 40

Brands by name

Popular brands

Load more brands