GMC 2000 Safari Owner'S Manual Download Page 132 | Manualshive

Page: 132 / 391

background image

2-57

3. Return to the HomeLink Transmitter in your

vehicle and firmly press and release the HomeLink
Transmitter button you have already programmed for
two to three seconds. Press and release the button
again (you may need to do this step up to three
times) to make sure that the HomeLink Transmitter
has been trained to the garage door opener motor
head unit. Check that the training was successful.
The motor head unit indicator light should no longer
be flashing.

The garage door opener should now recognize the
HomeLink Transmitter. You may either use the
HomeLink Transmitter or the hand

-

held transmitter

to open the garage door.

If after following these instructions, you still have
problems training the garage door opener, call the
manufacturer of the unit at 1

-

800

-

355

-

3515.

Erasing Channels

To erase all three programmed channels, hold down the
two outside buttons until the indicator light begins to
flash (after 20 seconds). Release both buttons.

Accessories

Accessories for the HomeLink Transmitter are available
from the manufacturer of the unit. If you would like
additional information, please call 1

-

800

-

355

-

3515.

«
...
130
131
132
133
134
...
»

Summary of Contents for 2000 Safari








































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Safari

Brand: KC HiLiTES Pages: 4

Brand: Warrior Products Pages: 2

Brand: GATmatic Pages: 13

Brand: Hama Pages: 40

Brand: Acura Pages: 2

Brand: Condor Pages: 2

Brand: Voxoa Pages: 48

2010 Challenger SRT

Brand: Dodge Pages: 444

Brand: ULTIMATE SPEED Pages: 56

Brand: Classic AutoAir Pages: 44

Brand: Kuda Pages: 3

Brand: Metra Electronics Pages: 10

Brand: Adaptiv Mini Pages: 4

DODGE AD100 1993

Brand: Chrysler Pages: 1502

Brand: Axxess Pages: 16

Brand: HAKR Pages: 10

Brand: Opel Pages: 233

Brand: Peiying Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands