manualshive.com logo in svg

GMC 2000 Safari, Owner'S Manual

The GMC 2000 Safari Owner's Manual is a comprehensive guide that provides step-by-step instructions and valuable information on operating and maintaining your vehicle. With a user-friendly format, this manual is available for free download at manualshive.com, allowing you to access it conveniently and keep your Safari running smoothly.

Share
Download
background image

4-7

Avoid needless heavy braking. Some people drive in
spurts 

--

 heavy acceleration followed by heavy 

braking 

--

 rather than keeping pace with traffic. This is a

mistake. Your brakes may not have time to cool between
hard stops. Your brakes will wear out much faster if you
do a lot of heavy braking. If you keep pace with the
traffic and allow realistic following distances, you will
eliminate a lot of unnecessary braking. That means
better braking and longer brake life.

If your engine ever stops while you’re driving, brake
normally but don’t pump your brakes. If you do, the
pedal may get harder to push down. If your engine
stops, you will still have some power brake assist. But
you will use it when you brake. Once the power assist is
used up, it may take longer to stop and the brake pedal
will be harder to push.

Anti-Lock Brakes (ABS)

Your vehicle has anti

-

lock brakes (ABS). ABS is an

advanced electronic braking system that will help
prevent a braking skid.

When you start your engine and begin to drive away,
your anti

-

lock brake system will check itself. You may

hear a momentary motor or clicking noise while this test
is going on. This is normal.

United States

Canada

If there’s a problem with the anti

-

lock brake system, this

warning light will stay on. See “Anti

-

Lock Brake

System Warning Light” in the Index.

Summary of Contents for 2000 Safari








































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Safari

GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Brand: GMC Pages: 140
Pacbrake 10475 Installation Manual preview
10475
Brand: Pacbrake Pages: 9
TATA Motors Nano Owner'S Manual & Service Book preview
Nano
Brand: TATA Motors Pages: 94
GÄN GA Manual preview
GA
Brand: GÄN Pages: 24
Saab B205 Installation Instructions Manual preview
B205
Brand: Saab Pages: 10
Warrior Products 10936 Installation Instructions preview
10936
Brand: Warrior Products Pages: 3
CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Brand: CITROEN Pages: 2
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Brand: Subaru Pages: 34
Edelbrock 6883 Instructions preview
6883
Brand: Edelbrock Pages: 2
Gator HUDGPS1 Quick Start Manual preview
HUDGPS1
Brand: Gator Pages: 2
Firestone Ride-Rite Air Helper Springs 2173 Installation Instructions preview
Ride-Rite Air Helper Springs 2173
Brand: Firestone Pages: 4
Pyle PLDCP3 User Manual preview
PLDCP3
Brand: Pyle Pages: 2
Columbia THERAPEDIC 2000 Instructions For Use Manual preview
THERAPEDIC 2000
Brand: Columbia Pages: 14
Blue Ox BX1120 Installation Instructions preview
BX1120
Brand: Blue Ox Pages: 5
Ford TRANSIT 2015 Quick Reference Manual preview
TRANSIT 2015
Brand: Ford Pages: 8
Edelbrock 67312 Installation Instructions preview
67312
Brand: Edelbrock Pages: 2
Navman N-series B2+ User Manual preview
N-series B2+
Brand: Navman Pages: 27
Mazda 2014 CX-9 User Manual preview
2014 CX-9
Brand: Mazda Pages: 604

Brands by name

Popular brands

Load more brands