GMC 2000 Safari Owner'S Manual Download Page 22

Page: 22 / 391

1-10

5. Lift up on the left and the right seat release levers at

the same time. The latches are near the floor on the
rear legs of the seat.

6. Lift up on the rear of the seat to remove the seat

assembly from the rear latch pins. Then, pull back
and lift the seat out of the vehicle.

Your seat release latch lever is sprung with a
two

stage mechanism. To fully release the latch, two

levels of lift effort will be required. First, a low effort
to overcome the first stage and then a moderate
effort to fully release the latch.

Summary of Contents for 2000 Safari







































































































































































































































































































































































































Search results

Summary of Contents for 2000 Safari

Reviews:

Related manuals for 2000 Safari

Brands by name

Popular brands

GMC 2000 Safari, Owner'S Manual

Search results

Summary of Contents for 2000 Safari

Reviews:

Related manuals for 2000 Safari

Brands by name

Popular brands