GMC 2000 Safari Owner'S Manual Download Page 86 | Manualshive

Page: 86 / 391

background image

2-11

Resynchronization

Resynchronization may be necessary due to the security
method used by this system. The transmitter does not
send the same signal twice to the receiver. The receiver
will not respond to a signal it has been sent previously.
This will prevent anyone from recording and playing
back the signal from the transmitter.

To resynchronize your transmitter, stand close to your
vehicle and simultaneously press and hold the LOCK
and UNLOCK buttons on the transmitter for eight
seconds. The door locks should cycle to confirm
synchronization. If the locks do not cycle, see your
dealer for service.

Sliding Door

To open the sliding side door, pull the handle toward the
back and slide the door to the rear until it rests in the
open position.

To close the sliding side door, pull the handle toward the
front and slide the door forward.

«
...
84
85
86
87
88
...
»

Summary of Contents for 2000 Safari








































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Safari

Brand: JAC Pages: 70

Brand: iDataLink Pages: 30

Brand: Triumph Pages: 86

LeisureWize EMOVE EM303A

Brand: Streetwize Pages: 20

Brand: Veigel Pages: 24

Brand: Cellular Line Pages: 25

Brand: Cadillac Pages: 402

Brand: Cobra Pages: 2

Brand: Yakima Pages: 15

Brand: Pontiac Pages: 20

Crossland X 2017

Brand: Vauxhall Pages: 245

Brand: FORM FIT Pages: 2

Brand: Grillo Pages: 71

1500 CLASSIC 2020

Brand: RAM Pages: 360

Brand: Whispbar Pages: 14

2010 Accord Coupe

Brand: Honda Pages: 410

Brand: FIRRAK Pages: 12

Filtercharger 57-9004

Brand: K&N Engineering Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands