manualshive.com logo in svg

Global Contract Bridges II, Installation Manual

Share
Download
Global Contract Bridges II Installation Manual Download Page 32

Page

•

  

globalcontract.com

31

• Summer 2017

GLOBAL

Contract

INSTALLATION GUIDELINES

Storage Mounted B3 Divider - Panel Frame Installation

STEP 1: Insert support bracket against the inner vertical wall as indicated above.

STEP 2: Secure support bracket through the inside of panel with provided ma-
chine screws. Holes in the bracket should line up with holes in panel.

STEP 3: Insert panel into the gap (as shown) until it hits the support bracket.

STEP 4: Once in place, fasten bracket to storage through the inside with provided 
screws. Repeat on 4 sides. At this point, the base feed (if applicable) should be 
installed. Base feed CAN NOT be installed once storage is back to back.

STEP 5: Top of storage should line up with each other and the end of the panel.

STEP 6: For installing units with power distribution modules, proceed to do so. 
After installing power distribution modules (if applicable) fi nish by closing the 
full fabric tile; or for units with a combo accessory tile & fabric, see following 
instructions.

1

2

3

5

6

4

NOT UL LISTED

Summary of Contents for Bridges II

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands