manualshive.com logo in svg

Global Contract Bridges II, Installation Manual

Share
Download
Global Contract Bridges II Installation Manual Download Page 26

Page

•

  

globalcontract.com

25

• Summer 2017

GLOBAL

Contract

INSTALLATION GUIDELINES

Perpendicular End of Run Dividers

Note: the Perpendicular end of a run divider can only be installed on rectangular legs. 
Remove vertical cable manager cover from both legs.

STEP 1: Align top brackets with pilot holes and secure with supplied screws.

STEP 2: Slide the End Of Run Divider top brackets between top of leg’s horizontal 
beam and the bottom of the work surface and secure with supplied screws. Note: two 
screws per bracket.

STEP 3: Insert and rotate the end of a run divider bottom bracket into the leg, slide it 
up against the bottom End Of Run Divider edge.

STEP 4: Align the brackets with pilot holes in as illustrated and secure with supplied 
screws.

Trim the vertical cable manager cover and snap it back in place.

2

4

3

Modesty Panel

Recessed modesty panel fl ip down bracket kit consists of two pairs of brackets.

STEP 1: Position the small brackets on the modesty panel so that the bracket’s wall 
with single hole A faces outer edge of the modesty.
Align brackets with pilot holes and secure with supplied screws. Ensure that the 
two supplied shoulder screws B are installed in the top, smaller holes (one per each 
bracket).

STEP 2: Position the large brackets against the bottom of the work surface panel so 
that the bracket’s wall with the oblong hole C faces table legs.
Align the second hole D (close to the bracket’ bend) with the third pilot hole E and 
secure with supplied screws. Ensure that the brackets are perpendicular to the work 
surface’s edge and secure the remaining screws.

1

2

D

C

E

A

B

STEP 3: Suspend the modesty panel off the brackets by inserting both shoulder 
screws through the bracket’s keyholes F.

STEP 4: Install joint connector screw as illustrated - the threaded stem screw G com-
ing in from the leg side. Tighten with Allen keys.

STEP 5: Hold the centre top edge of the modesty panel with one hand and the centre 
bottom edge of the modesty panel with the other hand.
Lift the modesty panel gently upward, making sure that both sides move up evenly. 
Pull the top edge gently out to disengage both shoulder screws and rotate downward.

Ensure that opening and closing action is smooth and both shoulder screws engage 
the keyholes easily.

3

4

G

F

NOT UL LISTED

Summary of Contents for Bridges II

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands