GE Digital Energy LP 33 Series Operating Manual Download Page 69

Page: 69 / 103

Modifications reserved

Page 69/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

7.5 COMMANDS

The

COMMANDS mode

is entered any time the “

COMMANDS

” key is pressed.

Allows the user to execute UPS operation commands.

In this mode the keys perform the following functions:

Return to HOME screen.

Scrolls forward to the next screen.

Scrolls forward to the next line.

Confirm the selection made.

It is possible to view any key functional description by pushing the key for more than 3 seconds.

Home\ Commands

COMMANDS

LAMP TEST

INVERTER

OFF

BOOSTER

(Service)

Commands screen 1

LAMP TEST

Signalling

LEDs

test and

buzzer

test (all LED should be lit

and blinking and the acoustical alarm should be activated).

INVERTER ON

Command to switch the inverter.

INVERTER OFF

Command to shutdown the inverter.

BOOSTER ON (Service)

Service only allowed.

Home\ Commands

COMMANDS

RESET TOTAL OFF

REQUEST

TOTAL

OFF

Commands screen 2

RESET TOTAL OFF

Restore of the command

“Total Off”

REQUEST TOTAL OFF

Command

“Total Off”

Screen sequence to execute the command

“Total Off”

Home\ Commands

Home\ Commands

COMMANDS

COMMANDS

RESET TOTAL OFF

REQUEST TOTAL OFF

CANCEL TOTAL OFF

EXECUTE TOTAL OFF

As the command procedure
of

“Total Off”

is finished the

“REQUEST TOTAL OFF”
screen appears again.

Summary of Contents for Digital Energy LP 33 Series








































































































Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands

GE Digital Energy LP 33 Series, Operating Manual

Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands