GE Digital Energy LP 33 Series Operating Manual Download Page 70

Page: 70 / 103

Modifications reserved

Page 70/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

8 OPERATION

8.1 PROCEDURES FOR SINGLE

LP 33 Series

8.1.1 Start-up of the

LP 33 Series

WARNING !

Before proceeding to turn on the UPS system, ensure that the AC and DC external
isolators are OFF, and prevent their inadverted operation.
Ensure that the output load distribution can be powered and all the output isolators
are open.

This procedure must be performed for the first start-up following the installation, with the UPS
completely switched Off and not powered.

Open the front door and make sure that:

•

All the

connections

to the input/output terminals of the UPS have been made correctly.

•

The

safety screens

are fixed in their position.

•

The switches

and

are open (Pos. O)

and the

“

External Battery fuses

”

are removed

LEDs on synoptic diagram

LED 1

Mains rectifier OK

LED 2

Mains bypass OK

LED 3

Rectifier ON

LED 4

Discharging battery

LED 5

Booster ON

LED 6

Charge battery ON

LED 7

Inverter available

LED 8

Inverter ON

LED 9

Q1 closed

LED 10

Automatic bypass ON

LED 11

Manual bypass Q2 ON

LED 12

Load on UPS

Q1 Output UPS switch

Q2 Manual

bypass

switch

Key Key Key LED LED LED

Inverter ON

Inverter OFF

Total Off

Stop Operation

Alarm

Operation

1. Switch-ON the mains voltage from the input distribution (both rectifier and bypass if separated).

Overall test results

Test1 OK

Test7 OK

Test2 OK

Test8 OK

Test3 OK

Test9 OK

Test4 OK

Test10 OK

Test5 OK

Test11 OK

Test6 OK

The UPS performs a

SELFTEST

A successful termination of the tests will be indicated with Overall
test results

“OK”

Commissioning cannot be continued should one or more tests result
to be negative.
Please contact in this case your

Service Centre

At this stage the electronic power supply is switched ON and the
buzzer sounds.

LED 1 (mains rectifier OK)

and

LED 2 (mains bypass OK)

must be lit.

Press

“MUTE”

key to reset

acoustical alarm

LED Alarm

remains lit.

Continue

►

Summary of Contents for Digital Energy LP 33 Series








































































































Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands

GE Digital Energy LP 33 Series, Operating Manual

Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands