GE Digital Energy LP 33 Series Operating Manual Download Page 56

Page: 56 / 103

Modifications reserved

Page 56/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

Home\Meter

MAINS

f 50

L1 230

L2 229

L3 231

BYPASS FREE

Bypass mains data screen

The frequency of the mains.

3-phase mains voltage PHASE /NEUTRAL.

Bypass

Bypass status: FREE / LOCKED.

Home\Meter

INVERTER

f 50

L1 230

L2 230

L3 230

T OK

SYNCHRONIZED

Inverter data screen

The output frequency of the

Inverter

3-phase output voltage PHASE/NEUTRAL.

The temperature of the inverter bridge (OK / MAX).

The synchronization status of the inverter with respect to

mains (Synchronized / Not Synchronized).

Home\Meter

MODULE LOAD

L1 :

230 V

72.0 A

50 %

L2 :

230 V

58.0 A

40 %

L3 :

230 V

43.0 A

30 %

LOAD ON INVERTER

Module load screen

… V

Output voltage PHASE/NEUTRAL for each phase.

… A

The output current as RMS values (RPA: value for
each UPS).

… %

The output load as percentage (RPA: value for
each UPS).

The source of the power supplied to the load.

Home\Meter

COUNTERS

Bypass mains failure

Rectifier mains failure

Overloads :

InvOperTime [h]

2135

UPSOperTime [h]

3125

Statistics screen

The total number of minor mains faults (bypass mains out

of tolerance faults).

The total number of times a gap of mains in the rectifier has
been reordered.

The total number of detected output overloads.

The total operating time for the

Inverter

(in hours).

The total operating time for the UPS (in hours).

Home\Meter

MAINS

NUMBER OF FAST TRANSIENTS

<2ms >2ms

>5ms

>10ms

ECO MODE RATE

70 %

ECO Mode statistic screen

This screen is enabled only for a single UPS, not for an

RPA

Parallel System

The number of fast transients occurred on the bypass

utility on the last seven days.

The statistic evaluation in % (100= good; 0= bad) of the

utility, for the

ECO

mode operation.

Summary of Contents for Digital Energy LP 33 Series








































































































Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands

GE Digital Energy LP 33 Series, Operating Manual

Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands