GE Digital Energy LP 33 Series Operating Manual Download Page 73

Page: 73 / 103

Modifications reserved

Page 73/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

2. Insert the external battery fuses

In case of GE battery cabinet: insert the fuses in their place and close fully the cover of fuse-

holder by using correctly the handle.

DANGER !

Before to perform this operation, check the right DC polarities on both side of the
switch/fuse holder!

3. Close the output switch Q1 (Pos. I).

The

load

is supplied by the mains through the

automatic bypass.

The

synoptic diagram

must display the status

“

LOAD SUPPLIED

BY AUTOMATIC BYPASS

”

Home\Meter

BOOSTER

f :

50.0

L1 :

397

L2 :

395

L3 :

393

Vp :

400

Vn :

400

Verify, selecting the screen

METERING/BOOSTER/

and

, that

the booster voltage has reached about

400 Vdc

4. Insert the inverter by pressing

“

Inverter ON

”

( I ) key.

Some seconds later the

load

will be transferred on

inverter

LED Alarm

turn Off and the

LED Operation

must be lit.

The

synoptic diagram

must display the status

“

LOAD SUPPLIED

BY INVERTER

”

5. Load

supply.

Your

LP 33 Series

UPS is now running in

VFI mode

, supplying power to the output.

Insert the

loads

one by one to the output of the UPS.

Check the output current value of

and

and check for correct load balance.

6. Operation mode selection.

LP 33 Series

is delivered normally selected for permanent

VFI

operation.

ECO mode

can be enabled and the

ECO Mode START

time &

ECO Mode STOP

time can be programmed for

each day of the week (see

Section 7.4 SETUP / ECO MODE)

END OF PROCEDURE

NOTE !

Even if the UPS is delivered with the

battery

fully charged, they could be partially

discharged during transportation or storage.
It is recommended to recharge the battery during at least 10 hours in order to
provide the complete

battery

energy stored to the load in the event of

mains failur

Summary of Contents for Digital Energy LP 33 Series








































































































Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands

GE Digital Energy LP 33 Series, Operating Manual

Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands