GE Digital Energy LP 33 Series Operating Manual Download Page 60 | Manualshive

Page: 60 / 103

background image

Modifications reserved

Page 60/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

Code

Alarm

Meaning

4531

LOAD ON MAINS

BY ERROR DETECTOR

Load is transferred to mains because the error detector
detected a disturbance on the output voltage.

4563

EMERGENCY OFF ACTIVATED

Alarm after detection of an Emergency Off from an external
safety device connected on Customer Interface.
Consequently K4, K6 and K7 open and shut down inverter,
booster and rectifier.

4570

OVERLOAD

The UPS-System is in an overload condition >125% on
inverter, or >150% on mains.
A sequence of “stop operation” starts.
Time out depending on load quantity.

4571

OVERLOAD: LOAD ON MAINS

With mains bypass supply available and load >115%, the
load is transferred on mains.
Load will be transferred again automatically on inverter
when load will be <100%.

4581

INVERTER AND MAINS

NOT SYNCHRONIZED

The voltages of mains and inverter are not synchronised,
which causes the opening of K6.

4697

BATTERY OVERTEMPERATURE

The battery temperature exceeds the value inserted in
parameter.
Disabled with parameter (service only).

4698

BATTERY POWER INSUFFICIENT

In case of utility failure, with the actual load, the autonomy
time would result below “stop operation” time (default 3
minutes).

4700

DC LOW

Battery voltage is at the lowest limit.
Shutdown of inverter until the battery voltage reaches the
value in respective parameter.

4900

LOAD LOCKED ON INVERTER

The load is locked on Inverter following 3 load transfers
within 30 seconds.
After time out of the value in respective parameter (default
30 seconds), bypass will be free.

4955

OVERTEMPERATURE

An overtemperature condition has been detected on
inverter.
Elapsed “stop operation” time, inverter shutdown.
With mains available, load is transferred on mains.

4998

LOAD OFF DUE TO

EXTENDED OVERLOAD

Load Off after time-out of “stop operation” for overload on
inverter or bypass (time depending on the % of overload).

4999

LOAD OFF DUE

TO LOW BATT. OR TEMP.

Load Off after time-out of “stop operation” with missing
mains due to battery low voltage or overtemperature
condition.

«
...
58
59
60
61
62
...
»

Summary of Contents for Digital Energy LP 33 Series








































































































Reviews:

No comments

Related manuals for Digital Energy LP 33 Series

Brand: Xantrex Pages: 3

Brand: GE Pages: 3

COILTHREAD KFS-30

Brand: Kato Pages: 2

Brand: Huskie Tools Pages: 16

Brand: Laguna Tools Pages: 17

Brand: Gardner Denver Pages: 27

Brand: Northern Pages: 11

Brand: OLI Pages: 2

Accelerator 2000

Brand: Rapid Pages: 76

Brand: Kamasa-TOOLS Pages: 12

Carlyle Tools 6-711A

Brand: Napa Pages: 16

Brand: TDK-Lambda Pages: 18

PolySprint NPS-1210A-1

Brand: Nitta Pages: 22

Brand: Samlexpower Pages: 5

Brand: Max Pages: 14

Brand: Akyga Pages: 4

Brand: Klein Tools Pages: 4

Brand: POWER ON BOARD Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands