GE Digital Energy LP 33 Series Operating Manual Download Page 66

Page: 66 / 103

Modifications reserved

Page 66/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

Home\Setup\User

MODEM

Tel 2

Tel 2 enabled

Tel 3

Tel 3 enabled

Tel 4

Tel 4 enabled

Modem screen 2

Tel 2

It records the

second dial-out number

Tel 2

enabled

This parameter

Y/N

specifies if the

second telephone number

will be used for dial-out.

Tel 3

It records the

third dial-out number

Tel 3 enabled

This parameter

Y/N

specifies if the

third

telephone number

will be used for dial-out.

Tel 4

It records the

fourth dial-out number

Tel 4 enabled

This parameter

Y/N

specifies if the

fourth telephone number

will be used for dial-out.

Home\Setup\User

DISPLAY

UPS name

LP Series

Language :

ENGLISH

Contrast

LCD Display screen

UPS Name

The user can choose the name of the UPS
model shown on the main page (max. 9
characters).

Language

This parameter allows the choice of
language used to display the information.

Valid choices are:

English, German, Italian, Spanish, French,

Finnish, Polish, Portuguese, Czech, Slovakian, Chinese,

Swedish, Russian and Dutch

Contrast

This parameter controls the contrast of the
LCD screen in ten steps (0 – 9).

Home\Setup\User

ECO MODE

Enabled :

DAY OF WEEK

d1 d2

HOURS / DAY

24 24 12 12 12 12 12

ECO MODE screen

This screen is enabled only for a single UPS, not for an

RPA

Parallel System

Enabled

This parameter (values

) enables or disables the

operation in

ECO Mode

If the value is

and the current time is in the interval for the

current day, the

ECO Mode

is active.

The activation / deactivation of

ECO Mode

is indicated each

time in the event list.

In order to check the

inverter

function, at least

1 minute

VFI

mode must be programmed during the week (the

Y/N

parameter is automatically disabled if this condition is not satisfied).

In case this minimum time in

VFI mode

is not respected, the

ECO Mode

will be disabled.

If the value is

, the UPS is normally operating in

VFI / double conversion mode

at all times.

DAY OF WEEK (d1 ÷ d7): Enabling time in function of weekdays

For the weekdays from

(Saturday to Friday)

the edit mode (edit day) allows to define time intervals when

the UPS is operating in

ECO Mode

. The hour is given in 24-hour format.

These intervals are defined by:

ECO Mode START

The hour of the day after which the

ECO Mode

is enabled.

The

ECO Mode

is enabled until the following

ECO Mode STOP

time is reached (the

ECO Mode

STOP

time of the same day if this is later than the

ECO Mode START

time, the

ECO Mode

STOP

time of the following day otherwise).

ECO Mode STOP

The hour of the day before which the

ECO Mode

is enabled.

The

ECO Mode

is enabled starting from the preceding

ECO Mode START

time (the

ECO Mode START

time of the

same day if this is earlier than the

ECO Mode STOP

time, the

ECO Mode START

time of the previous day otherwise).

Identical times for

ECO Mode START

and

ECO Mode STOP

maintain the existing mode only in case the previous

command was

ECO Mode START

and the following command will be

ECO Mode STOP

HOURS / DAY

The number of

ECO Mode

hours per weekday (from

- Saturday

- Friday

) is displayed in the operation

mode parameter window (ceiling value).

Summary of Contents for Digital Energy LP 33 Series








































































































Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands

GE Digital Energy LP 33 Series, Operating Manual

Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands