GE Digital Energy LP 33 Series Operating Manual Download Page 31

Page: 31 / 103

Modifications reserved

Page 31/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

White colour

without any anomaly

Red colour

anomaly evidence

Fig. 5.6-2 ShockWatch device

The package of the

LP 33 Series

equipped with

ShockWatch

(indicator for shock), and

TiltWatch

(indicator for overthrow) on the
outside.
These devices indicate an eventual
shock or overthrow during
transport.

Whenever these devices show a
possible anomaly, the UPS shall not
be commissioned before consulting
a

“Service Centre”

Fig. 5.6-3 TiltWatch device

NOTE !

A damaged UPS must never be installed or connected to

mains

battery

A detailed report of the damage is necessary for any indemnity claim.

PACKING MATERIAL RECYCLING

, in compliance with environment protection, use only environmentally

friendly material.
UPS packing materials must be recycled in compliance with all applicable
regulations.

Summary of Contents for Digital Energy LP 33 Series








































































































Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands

GE Digital Energy LP 33 Series, Operating Manual

Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands