GE Digital Energy LP 33 Series Operating Manual Download Page 78

Page: 78 / 103

Modifications reserved

Page 78/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

8.1.5 Restore to normal operation after “Total Off”

NOTE !

Make sure the UPS to be status of the activation of “

Total Off”

, i. e.

closed,

open and the

external battery fuses

connected.

View of the

synoptic diagram

after pressing the “

Total Off” key

•

All

Contactors

are open.

•

Booster, Inverter

and

Static-Switch

shutdown.

Home\Commands

COMMANDS

RESET TOTAL OFF

REQUEST TOTAL OFF

1. Reset

“

Total Off”.

Restore the command

“Total Off”

by entering the screen:

COMMANDS /

RESET TOTAL OFF

LED Alarm

is lit.

The load is supplied by the

mains

through the

automatic

bypass

The

booster

starts automatically.

The

synoptic diagram

must display the status

“

LOAD

SUPPLIED BY AUTOMATIC BYPASS

”

2. Insert the inverter by pressing

“

Inverter ON

”

( I ) key.

Some seconds later the

load

will be transferred on

inverter

LED Alarm

turn Off and the

LED Operation

must be lit.

The

synoptic diagram

must display the status

“

LOAD

SUPPLIED BY INVERTER

”

END OF PROCEDURE

Summary of Contents for Digital Energy LP 33 Series








































































































Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands

GE Digital Energy LP 33 Series, Operating Manual

Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands