GE Digital Energy LP 33 Series Operating Manual Download Page 79

Page: 79 / 103

Modifications reserved

Page 79/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

8.1.6 Restore to normal operation after “EPO – Emergency Power Off”

NOTE !

Make sure the UPS to be status of the activation of

“EPO - Emergency Power Off”

, i. e.

closed,

open and the

external battery fuses

connected.

View of the

synoptic diagram

after pressing the push-button “

EPO

- Emergency Power Off”

•

All

Contactors

are open.

•

Booster, Inverter

and

Static-Switch

shutdown.

1. Reset the “EPO” key.

Press

MUTE

key to reset

Alarm and Acoustical alarm

LED Alarm

remains lit.

Reset the UPS by pressing “Inverter OFF” ( O ) key.

The load is supplied by the

mains

through the

automatic

bypass

The

booster

starts automatically.

The

synoptic diagram

must display the status

“

LOAD

SUPPLIED BY AUTOMATIC BYPASS

”

3. Insert the inverter by pressing

“

Inverter ON

”

( I ) key.

Some seconds later the

load

will be transferred on

inverter

LED Alarm

turn Off and the

LED Operation

must be lit.

The

synoptic diagram

must display the status

“

LOAD

SUPPLIED BY INVERTER

”

END OF PROCEDURE

Summary of Contents for Digital Energy LP 33 Series








































































































Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands

GE Digital Energy LP 33 Series, Operating Manual

Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands