GE Digital Energy LP 33 Series Operating Manual Download Page 89

Page: 89 / 103

Modifications reserved

Page 89/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

8.2.6 Complete Parallel System shutdown

As a result of this procedure the

Parallel System

is completely switched OFF and not powered.

NOTE !

Follow this procedure only in case the

Parallel System

and the load must be

completely powered-down.

1. Press

“Total Off” key on anyone of the parallel units.

Open the output switch Q1 (Pos. 0) on all UPS units

3. Remove the external battery fuses on each unit

In case of GE battery cabinet:

−

Open fully and remove the cover of fuse-holder by using correctly the handle;

−

Remove the fuses from their place, re-install and close fully the cover of fuse-holder.

The

acoustical alarm

is activated, press

“MUTE”

key to reset it.

In order to discharge the DC link capacitors, insert the inverter by pressing

“

Inverter ON

”

( I ) key

on all UPS units.

Home\Meter

INVERTER

f :

50.0

L1 :

L2 :

L3 :

T :

SYNCHRONISED

Remark

Command

INVERTER ON

will be enabled only when the inverter

voltage of each phase decreases below

7 Vac

(about 30 seconds).

Home\Meter

BOOSTER

f :

50.0

L1 :

397

L2 :

395

L3 :

393

Vp :

Vn :

Before proceeding to step

, check on the display panel that the

link voltage

(both polarities)

and

has reached the max.

voltage of

5 Vdc

(about 30 seconds).

The

acoustical alarm

is activated, press

“MUTE”

key (from Home

screen) to reset it.

5. Disconnect the inverter, on all UPS units, by pressing

“

Inverter OFF

”

( O ) key and hold until the

LED Inverter (7) turns OFF.

Switch OFF the mains power, on all UPS units, at the AC input distribution panel.

END OF PROCEDURE

WARNING !

If the above procedure is not completely performed, it could cause
serious damages to the UPS.
In case the procedure described on step

“4 - Discharge DC link capacitors”

cannot

be completely performed, the DC capacitors could be charged with dangerous
voltage for a min.5 minutes.
Wait until capacitors are completely discharged before starting the UPS again.
Apart from the front door, do not open any other part of the UPS.

Summary of Contents for Digital Energy LP 33 Series








































































































Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands

GE Digital Energy LP 33 Series, Operating Manual

Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands