GE Digital Energy LP 33 Series Operating Manual Download Page 21

Page: 21 / 103

Modifications reserved

Page 21/103

OPM_LPS_33E_60K_M12_2GB_V010.doc

Operating Manual

LP 33 Series 60-80-100-120 kVA / S2

4.7 RECYCLING AT THE END OF SERVICE LIFE

NOTE !

This product has been designed to respect the
environment, using materials and components respecting

eco-design rules.
It does not contain CFCs (Carbon Fluor Clorid) or HCFCs
(Halogen Carbon Fluor Clorid)

RECYCLING AT THE END OF SERVICE LIFE

, in compliance with environment protection

recommends to the

User

that the UPS equipment, at the

end of its service life, must be recovered conforming to the
local applicable regulations.

WARNING !

Leads contained in the batteries is a dangerous substance
for the environment, therefore it must be correctly

recycled by specialised companies!

Summary of Contents for Digital Energy LP 33 Series








































































































Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands

GE Digital Energy LP 33 Series, Operating Manual

Search results

Summary of Contents for Digital Energy LP 33 Series

Reviews:

Related manuals for Digital Energy LP 33 Series

Brands by name

Popular brands