FujiFilm SD1125S2 Operation Manual Download Page 56

Page: 56 / 68

PART III INSPECTION AND SERVICE

3．LUBRICATION

(BEFORE / AFTER SEASON)

■Chute deflector fulcrum

■Travel clutch lever

■Work clutch lever

SD30-11

SDB3-03

■Backward emergency

■Side clutch lever

stop device

SF2-03-08

●

Do not lubricate the throttle lever fulcrum. Otherwise, holding power
of the lever decreases and the lever cannot be fixed.

●

Lubricate other sliding parts according to necessity.

●

Use genuine gear oil SAE 90 for lubrication.

4. GREASING

(BEFORE / AFTER SEASON)

■Travel idler

■Rotating part of chute

■Rolling fulcrum

SD30-27

SD30-07

03-8633-13

■Adjustment rod of

■Auger shaft

change lever friction

■Change lever sliding part

SE3-02

SD30-10

SF2-03-04

IMPORTANT

●

Be sure to use cold-resistant grease for greasing.

SDB3-03

SDB3-04

SDB3-05

SDB3-06

IMPORTANT

- 51 -

Summary of Contents for SD1125S2





































































Search results

Summary of Contents for SD1125S2

Reviews:

Related manuals for SD1125S2

Brands by name

Popular brands

FujiFilm SD1125S2, Operation Manual

Search results

Summary of Contents for SD1125S2

Reviews:

Related manuals for SD1125S2

Brands by name

Popular brands