FujiFilm SD1125S2 Operation Manual Download Page 54

Page: 54 / 68

PART III INSPECTION AND SERVICE

■REGULAR SERVICE LIST (REPLENISH, REFILL, LUBRICATION, GREASING）

Check

Change

Travel mission oil

2.0 L

☆

Auger mission oil

0.5 L

☆

Counter gear case oil

0.1 L

☆

Chute deflector fulcrum

Travel clutch lever
fulcrum

Side clutch lever
fulcrum

Work clutch lever
fulcrum

Backward emergency
stop device fulcrum

Sliding portion of
change lever

Adjustment rod of
change lever friction

Travel idler

Chute rotating part

Rolling fulcrum part

Auger shaft

●

For item with

☆

in page column, ask your dealer for service. If you do not have skill and experience,

ask your dealer for service of other item as well. Do not attempt to service the machine.

●

The interval time of service above is a standard. Actual interval time may differ according to work condition
and service situation.

HST oil tank

Before/after

the season,

when

necessary

Replenish/

Change

Time for inspection and change

(used time)

Capacity,

prescribed

amount

Sort

Oil

25.0 L

Replenish/

Change

uel

Replenish

Fuel tank

Genuine cold-resistant

grease

Genuine hydraulic oil

T-32

1st time: every 50H
From 2nd time: every
100H or every year

Between upper and

lower limits of the

oil tank scale.

1.5 L

Hydraulic pump oil

Lubrication

－

Refill

Engine oil for gasoline

10W-30,

SE class or higher

grade

eas

Check item

Unleaded gasoline for

automobiles

26, 50

1st time: Every 20H

From 2nd time: Every

50H or every year

Engine oil

Proper amount

Greasing

1.55 L

Genuine gear oil SAE

☆

26, 50

－

Page

Service

Before every

work

－

☆

- 49 -

Summary of Contents for SD1125S2





































































Search results

Summary of Contents for SD1125S2

Reviews:

Brands by name

Popular brands

FujiFilm SD1125S2, Operation Manual

Search results

Summary of Contents for SD1125S2

Reviews:

Brands by name

Popular brands