manualshive.com logo in svg

Fuji Xerox DocuPrint M255 df, User Manual

Share
Download
Fuji Xerox DocuPrint M255 df User Manual Download Page 119

Printer Connection and Software Installation

119

• WPS-PIN

NOTE: 

•

WPS-PIN is a method to authenticate and register devices required for wireless configuration, by entering PIN 
code to a printer and computer. This setting, performed through access point, is available only when the 
access points of your wireless router supports WPS.

•

Before WPS-PIN starts, you will need to enter your PIN code at the web page of the wireless access point. 
See the access point manual for the details.

1

On the operator panel, press the 

 (

System

) button.

2

Select 

Admin Menu

, and then press the 

 button.

3

Select 

Network

, and then press the 

 button.

4

Select 

WPS Setup

, and then press the 

 button.

5

Select 

PIN Code

, and then press the 

 button.

6

Take a note of PIN code displayed on the operator panel.

7

Select 

Start Configuration

, and then press the 

 button.

8

If SSID selection screen appears, select the SSID, and then press the 

 button.

9

Enter the PIN code of the printer at the web page of the wireless access point.

10

Wait a few minutes until the printer restarts to establish the wireless network.

11

Print a System Settings page from the operator panel.

a

Press the 

 (

System

) button.

b

Select 

Report/List

, and then press the 

 button.

c

Select 

System Settings

, and then press the 

 button.

The System Settings page is printed.

12

Confirm that “Link Quality” is shown as “Good”, “Acceptable” or “Low” on the report.

NOTE: 

•

When “Link Quality” is “No Reception”, check if the wireless settings are correctly configured.

•

If the wireless setting does not work, contact your system administrator or Fuji Xerox Customer Support 
Center.

Summary of Contents for DocuPrint M255 df








































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands