22.1 V-Link
22-9
•
Expansion code
When accessing to the memory shown below, set the expansion code in addition to the type and address.
* If there is no need to set the expansion code, set “00” (= 3030 in the ASCII code).
•
Port number
Set the port number used for 1 : n connection (multi-drop)
For 1 : 1 connection or n:1 connection (multi-link), the port number setting is not used. Alternatively, set “00” (= 3030 in
the ASCII code).
•
System reserved
Enter “0” (= 30 in the ASCII code) for the number of bytes.
The number of bytes for “system reserved” varies depending on the model.
Example:
Sum Check Code (SUM): 2 Bytes
Data is added up (SUM), and the lower one byte (8 bits) of the sum is converted into a two-digit ASCII code (hexadecimal).
A sum check code is shown below.
Example: Transmission mode: without CR/LF, with sum check
Command: 20 (data read)
Address:
10 words from $u1000 (03E8H)
When reading, a sum check will be performed as shown below.
Response Code: 2 Bytes
“ACK” code is received at normal termination, and “NAK” code at abnormal termination. The following table shows the details
of each code.
$P
PLC number 1 to 2
Mitsubishi Electric PLC
Slot No. of SPU memory
Yokogawa Electric PLC
CPU No.
Omron PLC
Bank number
Model
Bytes
Code (Hexadecimal)
ASCII
S8 internal memory
10
0000000000H
30303030303030303030
STX
Port No.
Command
Read words
Memory model
Memory type
Address
System reserved
ETX
SUM
01H
20H
0AH
00H
00H
03E8H
0 0 0 0 0 0 0 0 0 0H
B9H
02H
30H31H
32H30H
30H41H
30H30H
30H30H
30H 33H 45H 38H
30H 30H 30H 30H 30H 30H 30H 30H 30H 30H
03H
42H39H
02H + 30H + 31H + 32H + 30H + 30H + 41H + 30H + 30H + 30H + 30H + 30H + 33H + 45H + 38H
+ 30H + 30H + 30H + 30H + 30H + 30H + 30H + 30H + 30H + 30H + 03H =
4B9H
Code
Contents
ACK
00H
Normal termination
NAK
02H
Overrun/Framing error
An overrun or framing error is detected in the received data. Send the command again.
03H
Parity error
A parity error is detected in the received data. Send the command again.
04H
Sum check error
A sum error occurs with the received data.
06H
Count error
The memory read/write count is “0”.
0FH
ETX error
No ETX code is found.
11H
Character error
A character not used in the received data is found (other than 0 to F).
Check the character and send the command again.
12H
Command error
An invalid command is given.
13H
Memory setting error
The address or device number is invalid.
Summary of Contents for Monitouch S8 series
