Fuji Electric Monitouch S8 series, Connection Manual

Page: 116 / 406

7.2 Temperature Controller/Servo/Inverter Connection 7-31
Available Memory
The available memory setting range varies depending on the device. Be sure to set within the range available with the device
to be used. Use [TYPE] when assigning the indirect memory for macro programs.
*1 When a memory other than status is used, set the decimal point of the numerical display part to “3”.
*2 “0” is stored in the address for which “(Blank)” is indicated in the table below.
*3 For setting data, see “Memory: 18 (Setting Data)” described below.
Memory: 18 (Setting Data)
Memory TYPE Remarks
00
(data request of circuit No. 1 to 4)
*1
00H Double-word, read only
01
(data request of circuit No. 5 to 8)
*1
01H Double-word, read only
02
(data request of circuit No. 9, 10 or E)
*1
02H Double-word, read only
03
(Data request of the minimum/maximum voltage, power
factor of circuit 1 to 10, and invalid power)
*1 *2
03H Double-word, read only
09 (model code) 09H Read only
10 (operation status) 0AH Read only
11
(pre-alarm value)
*1
0BH Double-word, read only
12
(current value measurement data)
*1 *2
0CH Double-word, read only
13
(integrated value data)
*1 *2
0DH Double-word, read only
14
(demand measurement data)
*1 *2
0EH Double-word, read only
15
(data of a maximum value of demand measurement)
*1 *2
0FH Double-word, read only
16
(historical data 1)
*1 *2
10H Double-word, read only
17 (historical data 2) 11H Double-word, read only
18
(setting data)
*3
12H Double-word
Address F-MPC04/F-MPC04P/F-MPC04S FePSU F-MPC30/F-MPC50/F-MPC55V/F-MPC60B
00zz Wiring method (voltage measured) (Blank) CT primary rated current
01zz
Ratio of VT 1 (primary voltage)
*1
(Blank) Ratio of VT (primary voltage)
02zz
Ratio of VT 1 (secondary voltage)
*1
(Blank) Ratio of VT (secondary voltage)
03zz Demand average time Demand average time Rated frequency
04zz Frequency (Blank)
Protective INST (current setting )
*2
05zz Number of applicable circuits (Blank) Protective INST (output setting)
06zz Pulse multiplying factor (Blank)
Protective DT (current setting)
*2
07zz
Ratio of VT 2 (primary voltage)
*1
(Blank)
Protective DT (operation time)
*2
08zz
Ratio of VT 2 (secondary voltage)
*1
(Blank)
Protective DT (output setting)
*2
09zz Number of turns for CT2 secondary line (Blank) Protective OC (current setting)
10zz
CT primary current
*1
(Blank) Protective OC (characteristic)
11zz OCG sensitivity current (Blank)
Protective OC (time magnification)
*2
12zz
OCG operation time
*2
(Blank) Protective OC (output setting)
13zz Load pre-alarm sensitivity current (Blank)
Protective OCA overcurrent pre-alarm
(current setting)
14zz Load pre-alarm operation time (Blank)
Protective OCA overcurrent pre-alarm
(operation time)
15zz Automatic display circuit register (Blank)
Protective OCA overcurrent pre-alarm
(output setting)
16zz ZCT select (Blank)
Protective OCG (51G) (current setting)
*3
17zz VT select (Blank) Protective OCG (51G) (characteristic)
18zz (Blank) (Blank)
Protective OCG (51G) (time magnification)
*2
19zz (Blank) (Blank) Protective OCG (51G) (output setting)