Model D2424LVmkII Reference Manual (Names and Functions)
18
32. All Input LED
[ALL INPUT]
This is lit when all track input monitors are set to
ON by pressing the
[TRACK SHIFT]
key while pressing
the
[SHIFT]
key, and extinguished when set to OFF.
While in the SETUP mode, it is also possible to
automatically set it to all input monitors while the
recorder is in the stop mode.
35. Foot switch jack
[FOOT SW]
(Connector: PHONE jack)
Punch in/out (also for rehearsal) or PLAY/STOP of
the recorder can be done by foot by connecting the
optional foot switch.
The foot switch function can be changed in the
SETUP mode. It will not function for punch in/out
function in the initial setting.).
33. Track shift LED [9-16, 17-24] (green)
This is lit when the selectable recording track is
shifted to 9-16 or 17-24.
<Note>:
Be sure to use an “
unlatch type
” foot switch
if you use a foot switch. Otherwise, a malfunction
could occur.
* Refer to page “
46
” for information about Punch
In/Out recording using the foot switch.
31. Shift key
[SHIFT]
Press a key, or button while holding down the
[SHIFT]
key to activate the following “
shift-invoked
”
functions.
[VARI PITCH] key
[RECORD TRACK]
select keys
[TRACK SHIFT] key
[RECORD] button
[CLIPBOARD IN/OUT] key
[AUTO PUNCH IN/OUT] key
[AUTO RTN START/END] key
[EXIT/NO] key
[EXECUTE/YES] key
[DISP SEL] key
[EDIT] key
[SETUP] key
[UNDO/REDO] key
Executes the envelope function of the
selected track.
Switches ON/OFF of the input monitor for
all tracks.
Switches SAFE-READY for all tracks.
Executes preview of the stored point of
each memory key.
Reserved for future function. Not
supported by this version.
Switches the slave mode ON/OFF.
Selects the time base.
Switches TC READY ON/OFF.
Enters the TC GEN setup mode.
Enters the multiple undo executing mode.
* Refer to page “
108
” for details on the SETUP mode.
* Refer to the
"APPENDIX"
at end of this manual in
regards to the TC generator mode.
* Refer to page "
69
" for details on multiple undo
function.
* Refer to the
"Quick Operation Guide"
in regards to
editing of Vari Pitch data.
* Refer to page "
67
" for details on preview.
* Refer to page "
65
" for details on the envelope
function.
Enters the vari pitch data editing mode.
36. Meter display
This meter display shows the signal level and
settings.
* Refer to the “Display section” on page “
19
.”
* For details, refer to page
29
at end of this manual.
Key with SHIFT function
Function
* Refer to page “
43
” for details about Punch In/
Out operation.
<Note>:
If a correct value is not stored, pressing
the
[AUTO PUNCH]
key will not enable the function,
and the message “
Void Out Point!”
will appear.
If a correct value is not stored, pressing the
[AUTO
PUNCH]
key will not turn on the function, and the
message “
Void Out Point!
” will alert you. In this case,
set a correct value for the Auto Punch In/Out point.
Also, the function is not turned on when you press
the
[AUTO PUNCH]
key if the disk does not have
enough recording space. The display will indicate
“
-**H **M **S **F Over.
”
34. Hard disk access LED (green)
This LED lights up or blinks when the hard disk is
writing or reading data.
<CAUTION>:
Do not turn the power off while this
LED is lit or blinking. Otherwise, data on the hard
disk may be damaged.
[NEXT] key
The recorder will locate to the head of the
next time code event, subsequent to the
recorded time code. This functions only
when an optional Model 8346 is installed.
The recorder will locate to the head of the
time code event previous to the recorded
time code.
This functions only when an optional Model
8346 is installed.
[PREV] key
[STORE] key
Holds the current time data, which you can
edit.
Summary of Contents for D2424LVmk2
Page 157: ......
