Model D2424LVmkII Reference Manual (Editing Tracks)
73
Flashing
• Executing Paste
(4)
Press the [EXECUTE/YES] key again.
The display indication enables you set the number
of the paste operations. The number and “
SURE?
”
flash. At this time, the flashing
[RECORD TRACK]
indicator becomes continuously lit.
(5)
Select a destination track to paste data.
(8)
Press the [EXIT/NO] key or the [STOP] button.
The recorder exits edit mode and displays the
previous Time Base indication.
(9)
Turn off the [RECORD TRACK] select key of the
copy (or move) source track.
<Note>:
If you try to execute the paste
operation by pressing the
[EXECUTE/YES]
key
when the disk has insufficient free space, “
Over
!”
appears on the display and edit mode is
cancelled. In this case, you need to delete
unnecessary data or programs.
• Refer to the following section, “Erase,”
“Deleting a Program,” or “Duplicating a
Program.”
• Refer to page “
76
” for more information on
erasing.
• Refer to page “
40
” for more information on
deleting a program.
• Refer to page “
39
” for more information on
duplicating a program.
• Single Undo/Redo Paste
You can single undo or redo a Copy & Paste
and Move & Paste operation.
•
To restore the data that existed prior to the paste
operation, press the [UNDO/REDO] key.
•
To restore the pasted data after you undo the paste
operation, press the [UNDO/REDO] key again.
When you press the [
UNDO/REDO
] key, the recorder
will undo or redo the operation immediately, and
display “
Undo !
” or “
Redo !
” and “
COMPLETED !
”.
Track display ( ) of the item to be copied (or moved) will change to lit.
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
24
∞
42
OL
0
30
24
18
12
9
6
3
SURE?
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Flashing
• Checking the clipboard data
•
Hold down the [STOP] button and press the [PLAY]
button.
The recorder indicates whether the sound data on
the clipboard is a copied data or moved data (“
Copy
Clip
” or “
Move Clip
”) and plays the data (this is called
“
clipboard playback
”). Monitor the playback sound
through the mixer channels that correspond to the
copied (or moved) tracks. During clipboard
playback, the indicates of the [
RECORD TRACK
]
select key for the copied (or moved) track will flash.
•
Press the [EDIT] key again to get ready for the paste
operation.
“
Copy Paste?
” or “
Move Paste?
” flashes on the
display.
(6)
Turn the Jog dial to enter the number of repeats
(Repeat = **).
You can enter up to 99.
However, this is automatically limited by the
available recording source on the disk.
That is, if the disk has enough free space, you can
set up to 99 repeats. If the disk has only a small
amount of free space, the Jog dial allows you to set
a lower number of repeats.
(7)
Press the [EXECUTE/YES] key.
“
Copy Paste
” (or “
Move Paste
”) flashes and the
duration of the pasted data appears as a negative
number on the display.
• If paste is to be done on the same track, it is
not necessary to select the track.
• Changing the destination track for paste is
permissible to a mono track or adjacent two
tracks in odd and even numbers (1-2, 3-4, 5-6,
etc.) only when the copy (or move) data is on
the clip board.
For this procedure, if the
[RECORD TRACK]
select key of the track to be changed is pressed,
and an objective track for pasting can be
selected.
• If a multiple number of tracks (1-3, 5-8, etc.)
other than those above had been copied (or
moved), paste can be done only to the same
track as that of the copy (or move) originating
track. The track cannot be selected even though
the
[RECORD TRACK]
select key is pressed.
This number will count down as the paste operation
proceeds. When the paste operation is complete,
the flashing “
Copy Paste
” (or “
Move Paste
”) lights
up continuously, and “
COMPLETED !
” is displayed.
<Note>:
This function only works when this
recorder is in the stop mode.
<Note>:
If you perform one of the following
operations after you use the Copy & Paste or
Move and Paste operation, the Undo/Redo
function will no longer be effective.
1. If a new recording has been made.
2. When a new editing job is executed (such
as Copy & Paste, Move & Paste, Erase).
3. While in the AUTO PUNCH ON mode,
when the AUTO PUNCH IN point is
passed in the PLAY (or RECORD) mode.
4. If the power was switched off.
5. If program select was executed.
6. When multiple undo is executed.
Summary of Contents for D2424LVmk2
Page 157: ......
