47
Model D2424LVmkII Reference Manual (Punch In/Out)
Manual Punch In/Out take
You can proceed to record if you are satisfied
with the recording level, foot switch timing, and
rehearsal.
<Note>:
You cannot record a second take during the
Manual Punch In/Out operation without stopping the
recorder. That is, the recorder will continue playing
after you finish recording a take, but you cannot record
another take by pressing the foot switch.
(1)
Confirm that Rehearsal mode is cancelled, and start
playing the recorder from a point slightly before
the desired Punch In point.
(2)
Play the guitar, accompanying the playback of
tracks 1 to 8.
(3)
Press the foot switch at the desired Punch In point.
Press the foot switch again at the desired Punch
Out point.
The recorder enters recording mode at the Punch
In point, and cancels recording mode at the Punch
Out point.
(4)
Press the [STOP] button.
(5)
Play track 3 and check the result of Punch In/Out.
<Hint>
You can use the [
PLAY
] button and the [
RECORD
]
button, instead of using the foot switch.
Follow the steps below.
This method also does not allow you to record
another take unless you stop the recorder first.
Procedure:
1.
Press the [PLAY] button to start playback from
a point slightly before the Punch In point.
2.
Press the [RECORD] button while holding down
the [PLAY] button at the desired Punch In point.
(Punch In recording starts.)
3.
Press the [PLAY] button at the desired Punch Out
point. (Recording is punched out.)
• If you press only the [
RECORD
] button in both
steps 2 and 3, you can rehearse Punch In/Out.
Single Undo/Redo
You can single undo or redo Manual Punch In/
Out recording.
Press the [
UNDO/REDO
] key after recording is
complete to restore the conditions that existed
prior to the recording.
Press the [
UNDO/REDO
] key again to restore the
conditions that existed after the recording.
However, the procedures explained here is for
Single Undo/Redo and there are limitations as
written in the Notes below. If the current drive
was formatted with the multiple undo function
ON, Multiple Undo is also possible.
Refer to page “
69
” for details on the Multiple
Undo function.
<Notes at executing single undo/redo>
Note-1
: This function only works when this
recorder is in the stop mode.
Note-2
: After finishing manual punch in/out,
please note that single Undo/Redo is not possible
if the following have been executed.
• If a new recording has been made.
• When a new editing job is executed (such as
Copy & Paste, Move & Paste, or Erase).
• When in the AUTO PUNCH ON mode, when
the AUTO PUNCH IN point is passed in the
PLAY (or RECORD) mode.
• If the power was switched off.
• If program select was executed.
• When multiple undo is executed.
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
Track 7
Track 8
This part is changed.
Playback end point
Playback start point
Punch In point
(Take In)
Punch Out point
(Take Out)
All tracks are in playback
monitoring mode.
Press the foot switch
at the Punch In point.
Only track 3 in input monitorin,
and data will be recorded.
The RECORD LED lights up
in this area.
All tracks are in playback
monitoring mode.
Press the foot switch
at the Punch Out point.
<Caution after Punch Out>
In an FS=44.1kHz program, the simultaneously
recordable number of tracks is a maximum of 8.
In an FS=88.2/96kHz program, the maximum is 2 tracks
in which “seamless punch out” without mute can be
executed.
In simultaneous recording beyond this number, the
recorder will be muted for 3-5 seconds after punch out
but during actual recording, it will be a seamless punch
out. Depending on the speed of the hard disk being
used, when recording a fewer number of simultaneous
tracks than mentioned above, the recorder will also be
muted, but this poses no problem during actual
recording.
Summary of Contents for D2424LVmk2
Page 157: ......
