39
Model D2424LVmkII Reference Manual (Handling Programs)
Duplicating a Program
<Notes>
* Duplicating a program is possible only when the Multiple Undo function is set to ON when formatting the
current drive. In a current drive with this setting at OFF, the “
PGM Duplicate?
” message will not display when
pressing the
[EDIT]
key mentioned below.
* The program which can be duplicated must be the currently active program.
Therefore, the program you wish to duplicate must be activated prior to executing the duplicating mode.
To enter a title:
• Turn the Jog dial, or pressing the [NEXT] key and
[PREV] key for the flashing cursor to voluntarily input
alphanumerics.
Press the
[PREV]
key/
[NEXT]
key and the recorder will
jump to the letters/symbols listed below (small square
position).
• Move the flashing cursor with the Shuttle dial.
• You can input the following alphanumerics and
symbols.
Titles can contain up to 16 alphanumeric characters.
(6)
When you finish entering the title, press the
[EXECUTE/YES] key.
Program 2 (PGM 02) and its title are set.
The display shows the ABS Time Base indication of
the Program.
(7)
Press the [EXIT/NO] key, or [STOP] button.
<Important!>
• When you create a new Program by
selecting the “
New PGM ?
” menu, a new
Program is created with an increment
number.
That is, if only one Program exists and when
you create a new Program, it will be named
Program 2. If Programs 1-5 already exist, a
new Program number will be 6.
• Remember that producing new programs
gradually decreases recordable disk space.
If disk space is insufficient, or if 99
programs have already been created, you
cannot create more new programs.
If a new program is attempted, “
Can’t New
PGM!
” will indicate that the operation is
invalid.
Any program content (Recording data/various setup items) can be duplicated but with a separate
program number.
(1)
With this recorder in the stop mode, press the
[EDIT] key to display “PGM Duplicate?” (“?”
flashes).
(2)
Press the [EXECUTE/YES] key.
As an example, the following is displayed and
“
SURE?
” will flash. This means that program 01
will be duplicated for program 05, the new program
05. Refer see
<Note>
below.
<Note>:
The program to be duplicated will be
assigned with a program number following that
of the program presently existing in the disk.
If “
Duplicate P01 > 05
” is displayed as in the
previous example, this indicates that four
programs presently exist in the disk and that
the new program will be number 05.
If the duplicated program is to be checked or
you wish to switch to this program, refer to the
next item “
Selecting a program
.”
(3)
Press the [EXECUTE/YES] key again.
The display will change to head of the duplicated
original program (P01 in this example), and
“
COMPLETED!
” will light.
(4)
Press the [EXIT/NO] key (or [STOP] button).
“
COMPLETED!
” will be extinguished.
By following these procedures, the same content in
program 01 is duplicated in program 05.
Flashing
Flashing
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
24
∞
42
OL
0
30
24
18
12
9
6
3
SURE?
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Summary of Contents for D2424LVmk2
Page 157: ......
